Anest Iwata WA-M220 Manuel D'instructions D'utilisation page 5

WA-M220, WA-220L Automatic Spray Gun
4. To adjust fluid needle packing set (3-4), first tighten it by hand while fluid nee-
dle set (2-2) is inserted. Then tighten it further about 1/6 turn (60-degree) by
wrench. When you remove needle packing set (3-4), do not leave plastic piece
of needle packing set (3-4) in the gun body.
IMPORTANT: If you tighten fluid needle packing set (3-4) too much, fluid needle
set (2-2) does not move smoothly, resulting in paint leakage from tip of fluid
nozzle (2-1). Try to adjust it carefully while pulling and pushing fluid needle
set (2-2) by hand checking its movement. If it is tightened too much, first fully
loosen it, then tighten it again carefully. After, assemble gun completely while
pulling piston (4) and checking movement of fluid needle set (2-2). If fluid needle
set (2-2) does not move smoothly, disassemble again and try to adjust it with
the same process.
5. Assemble gun body. Insert filler block nut to hole of rear part of gun body and
insert pin of the front part of gun body to the hole positioned on the front of
rear part of gun body as indicated. Connect front part with the rear part of gun
body, tightening 2 hex. socket head bolts (3-6) equally while fluid needle (2-2)
is inserted to get right centre position. While tightening the 2 hex. socket head
bolts (3-6) to accurately adhere the rear part of the gun to the front part, make
sure that the contact planes are at the same level.
IMPORTANT: Tighten 2 hex. socket head bolts (3-6) while fluid needle set
(2-2) is inserted to avoid that fluid needle set (2-2) will not move smoothly.
The rear part of gun body should be adhered to front part and the 2 contact
planes with manifold (12) should be at the same level, to avoid air and fluid
leakage. Tighten 2 hex. socket head bolts (3-6) equally.
Tool: Hex. Socket screw key (width 4mm) - Hex socket head bolt.
6. Assemble piston set (4). Screw rear section of fluid needle set (2-2) into piston
(4) and insert piston set (4) into the gun body. Apply grease to piston packing
(4-1) and O'rings. ∆ marks are indicated on bottom side of piston. When you
insert piston set (4) into the gun body, please make sure the position of ∆marks
are correct. ∆ marks must be positioned upper side and bottom side of gun
body.
IMPORTANT: Apply grease to piston packing (4-1) and O'rings to avoid that
piston set (4) does not move smoothly.
7. Assemble fluid nozzle (2-1) and air cap set (1).
Tighten fluid nozzle (2-1) and air cap set (1) to the gun body.
IMPORTANT: Fluid nozzle (2-1) should be tightened firmly in order to avoid fluid
leakage and fluttering.
Tools : Wrench (width 19mm) - Fluid nozzle
8. Position of the 2 horns of the air cap set (1), for easier assembly.
The body side has 1 pin to determine air cap position correctly (Vertical or
Horizontal). The air cap has 2 pins for the same function, so air cap can move
between the 2 pins 90°. If the air cap is installed correctly, according to air cap
marking, it will be possible to get the proper position.
IMPORTANT: Turn air cap (1) and when 2 pins hit, tighten air cap cover and fix
it. Horn position is horizontal or vertical.
9. Assemble fluid needle set (2-2), fluid needle valve spring (5), piston
spring (6) and fluid adj. set (7) to gun body. Apply Vaseline or oil to thread
section of fluid adj. set (7) and insert it into gun body while keeping it fully
opened.
IMPORTANT: If fluid adj. set (7) is not fully opened, tip seat section of it can
contact and damage fluid nozzle (2-1) and cause seizure thread.
Tool: Wrench (width 32mm) - Fluid adj. set
10. Turn pattern adj. set (11) counter-clockwise to fully open. And then tighten
pattern adj. guide into manifold (12).
IMPORTANT: If pattern adj. set (11) is not fully opened, tip of it can contact and
damage tip of manifold set (12) and cause seizure of thread.
Tool: Wrench (width 13mm) pattern adj. knob
11. Connect the gun to the manifold (12). Gun is adhered to manifold firmly.
Gun should be adhered to manifold (12) to avoid air and fluid leakage.
All manuals and user guides at all-guides.com
4
5
6
7
9
Hallow Upper
Hole front
Marks
O'rings
8
Pins
11
1. Put gun to manifold 2. Turn wing bolt set clockwise to fix.
EN
Plastic piece
White
Pin Hole
Adhered
Apply grease
Piston
packings
Pin
10
5