Télécharger Imprimer la page

Kenmore 587.1440 Serie Guide D'utilisation Et D'entretien page 13

Publicité

Les langues disponibles

Les langues disponibles

Connecting
and
Disconnecting
the
Portable
Dishwasher
The portable
dishwasher
must be connected
to a faucet
and electrical
outlet each time it is used. Follow
directions
on this page to properly
connect
dishwasher.
Faucet Adapter
IMPORTANT:
Make sure door is latched
before
moving
dishwasher.
Assembly
(Figure
A)
The power cord, faucet
coupler
and hoses are located
in a compartment
in
back of dishwasher.
A special
adapter
must be installed
on faucet before you
can connect
dishwasher
(Figure A).
1. Remove
faucet
adapter
assembly
from literature
package.
2. Unscrew
existing
sink faucet
aerator.
3. Check faucet
spout to see if threads
are inside or outside.
• If threads
are on inside of faucet
spout, use both thick and thin rubber
washers.
• If threads
are on outside of faucet
spout, use thin rubber washer
only.
• If faucet
has no threads,
an adapter
kit with instructions
for attachment
to
a non-threaded
spout is available
at most hardware
stores.
4. Assemble
faucet
spout as shown in Figure A. Make sure the two brass
screens
are located
below the rubber washers.
Connecting
the Portable
Faucet Adapter
Assembly
(Figure B)
Electric
Shock
Hazard
Avoid
fire hazard
or
electrical
shock.
Do
not use an adapter
plug, extension
cord or
remove
grounding
prong
from electrical
power
cord.
Failure
to
follow
this warning
can
cause
serious
injury,
fire or death.
Grounding
type
wall
receptacle
Do not under
any
circumstances
cut,
remove
or bypass
the grounding
prong
from
this
plug.
Connecting
the Portable
Dishwasher
1. Run water at faucet
until it is hot. Turn off faucet.
2. Pull hoses out of compartment.
3. Push collar down and slip faucet connector
onto faucet
adapter
(Figure
B).
4. When connector
snaps into place, release
collar.
5. Slowly turn on hot water all the way.
6. Plug power cord into grounded
outlet.
Disconnecting
the Portable
Dishwasher
1. When cycle has finished,
turn off hot water.
2. Press red button on coupler
to release
water pressure.
3. Press down on collar to release coupler.
4.
Empty remaining
water from coupler
and return it to compartment.
5. Unplug power
cord and return it to compartment.
IMPORTANT:
A sink spray hose can burst
due to constant
water
pressure
while
in use. If your spray hose is installed
on same water line
as the dishwasher,
it is your responsibility
to disconnect
sink's
spray
hose and to plug hole.
Electrical
Connection
for a Portable
Dishwasher
An electrical
supply of 120 volts, 60 Hz, AC only, 15 amps is required.
For
your safety,
the dishwasher
must be grounded.
If there is a malfunction
or
breakdown,
grounding
will reduce
risk of electrical
shock. This dishwasher
has a power cord with a 3-prong
grounding
plug. It must be plugged
into a
mating 3-prong
grounding
type receptacle,
installed
and grounded
in
accordance
with the National
Electrical
Code and any local codes and
ordinances.
13

Publicité

loading

Ce manuel est également adapté pour:

587.1441 serie587.14403400587.14402400587.14409400