BorMann PRO BBC9010 Mode D'emploi page 3

EN
1
2
3
Operating instructions
Connecting to the battery
1) Identify polarity of battery posts. The positive battery terminal is typically marked by these letters or symbol (POS,P,+). The negative battery terminal is typ-
ically marked by these letters or symbol (NEG,N,-).
2) Do not make any connections to the carburettor, fuel lines, or thin metal parts.
3) Identify if you have a negative or positive grounded vehicle. This can be done by identifying which battery post (NEG or POS) is connected to the chassis.
4) For a negative grounded vehicle (most common): connect the RED POSITIVE jumper clamp first to the positive battery terminal, then connect the BLACK
NEGATIVE jumper clamp to the negative battery terminal or vehicle chassis.
5) For a positive grounded vehicle (very uncommon): connect the BLACK NEGATIVE jumper clamp first to the negative battery terminal, then connect the RED
POSITIVE jumper clamp to the positive battery terminal or vehicle chassis.
6) When disconnecting, disconnect in the reverse sequence, removing the negative first (or positive first for positive ground systems).
Jump starting
1) This unit is only for emergency use, not for frequent commercial use! Need press Engine Start On/Off button once to activate this function. Do not attempt
to jumpstart your vehicle when the Device battery capacity is below 20%.
2) Turn off the vehicle ignition and all accessories (radios, lights, air conditioners, etc.), and disconnect electronic devices.
3) Connect the jumper clamps to the correct polarity battery terminals.
4) Connect the jumper cables to the ENGINE START socket of Device.
5) Try starting the vehicle (turn on the ignition switch). Most vehicles will immediately start. Stop if the vehicle does not start after 5 seconds of engine cranking.
The jumpstart feature is designed for short term operation only, and more than 5 seconds may cause damage to the unit. Allow the jump starter to cool down
for at least 3 minutes after each jumpstarting.
6) Do remember to press Engine Start On/Off button again to stop the output immediately after engine starts and disconnect jumper clamps from vehicle
battery terminals.
Note: when in reverse connection or when vehicle battery voltage is higher than Device voltage, the jumpstarting function cannot be operated.
Note: Device has the mandatory boost function (by pressing and holding Engine Start On/Off button for 3 seconds). Under normal circumstances, do not use
the mandatory operations. The spark proof, reverse polarity protection and short circuit protection features are disabled in mandatory function. Pay very close
attention to the polarity of the battery before using this mode. Do not allow the positive and negative battery clamps to touch or connect to each other as the
item will generate sparks and high heat if not used properly.
Charging
This product is partially charged from the manufacturer. Fully charge the unit immediately after purchase. In order to prolong the product life, be sure to fully
recharge the unit after each jumpstarting, or every 3 months even if this unit has not been used. If battery voltage in the Device is too low, this item will shut
off to prevent damage to itself. Recharge the unit as soon as possible to be activated and fully charge it to ensure long battery life. In addition, we recommend
not to charge and discharge the unit at the same time.
AC Charging:
1) Insert AC charging adapter into charging jack of the unit.
2) Plug the other end of AC charging adapter into a wall socket.
3) Fully charge the unit.
4) When charging is complete, unplug the AC charging adapter from the wall socket first, then from the charging jack on the Device.
DC Charging in Your Vehicle:
1) Turn the vehicle engine on.
2) Insert the DC charging adapter into the charging jack of the unit.
3) Plug the other end of DC charging adapter into vehicle's cigarette lighter socket.
4) Fully charge the unit. Engine must keep running during entire charge.
5) When charging is completed, unplug the DC charging adapter from the vehicle first, then from the charging jack on the Device.
3
6
5
4
WWW.NIKOLAOUTOOLS.GR
Icon 1: Flashlight is turned on.
Icon 2: When cable clamps are correctly connected with vehicle battery, this
icon is solid on; when in reverse connection, this icon slowly flashes; when
vehicle battery voltage is higher than Device voltage, this icon quickly flashes.
Icon 3: Engine Start output or 12V/10A DC output is ready.
Icon 4: Device is in charging and Input Charging LED is lit as well.
Icon 5: Shows battery residual capacity.
Icon 6: USB output is ready.