Bpt Futura X1 Mode D'emploi page 3

English
Description of device
Adjusting ring (high-medium-low)
Brightness (function available with video activated)
Colour saturation (function available with video activated)
Auxiliary 1 (function available even when communication is not
active if the system allows it)
Auxiliary 2 / Porter call (blue LED)
Intercom call
Select receivers from 5÷8 (blue LED)
Activate/deactivate communication (blue LED)
Disable ring/Mute (red LED)
Panic (red LED)
Activate and select entry panel.
This function is available only when the line is free.
Door lock release (blue LED)
In systems designed to accommodate this signal, during a call
from an entry panel or in self-connection, the permanently lit
LED indicates that the door is open.
Buttons lock
Press and hold down button for 3 seconds; the buttons will not respond to
pressure for 30 seconds to enable cleaning of the device.
If more than one button is pressed at the same time, or repeatedly by accident,
the buttons lock will be automatically activated for 10 seconds.
The buttons lock is cancelled if there is an incoming call.
Note: Only use soft, dry or slightly damp cloths to clean the terminal; do
not use any chemical products.
Standard functions
Answering a call
When there is a call, at the same time as it starts ringing, the master devices
will display the picture coming in from the entry panel.
To answer the call press button
To mute the audio to the entry panel press button
To open the door of the entry panel displayed, press button
To terminate the call press button
The call will be terminated automatically after 60 seconds.
Note: On some types of system the icon
will appear on the screen that warns that the door is open.
Self-connection
To see the picture taken by the entry panel without activating audio commu-
nication, press button .
Where there are several entry panels or video cameras connected to the
system, press button again to show in succession the pictures taken by
these devices.
To start audio communication with the entry panel displayed, press button
Activating auxiliary commands
Buttons and can be associated to auxiliary commands (switching on stair
light, opening gate, etc.).
The buttons are enabled when communication is active, button can be active
even when there is no active communication if the system's configuration
allows it.
Disabling ring tone
To disable the ring tone press button
.
.
.
.
will light up or a special icon
, the relative LED comes on.
The ring tone will be disabled for all call types; consequently, the receipt of a
call from the entry panel will ONLY activate the video. To reactivate the ring
tone, press button again.
Video toggle function
In systems with several receivers, when there is a call, the caller's picture is
displayed only on those receivers configured as "MASTER"s.
To display the caller's picture on a "SLAVE" receiver, press button
To enable audio communication press button
Intercom
Intercom calls
In systems with several receivers, select the number of the desired receiver in
order to make the call. Press button (LED on) to be able to select receivers
from 5 to 8.
After selecting the desired receiver, the receiver that's calling will emit a line
free tone, while the receiver being called will ring.
To answer the call press button
Transferring a call
With an active communication, select the receiver you wish to transfer the
call to (the receiver that's calling will emit a line free tone, while the receiver
being called will ring).
To answer the call press button
Once audio connection is made with the desired receiver, press
the call.
The receiver that receives the call can also transfer it.
Porter functions
Porter call notification
The porter can send a notification asking to be called back. The notification
is marked by LED Aux2 coming on and remains active until the porter is
called back.
To call the porter press button .
Porter call request
It is possible to send a notification to the porter asking to be called back. To send
the request to the porter press button , the porter will receive a notification
with the number of the caller.
Panic button function
Press button for at least 1", the receiver will beep and the red LED will
come on.
The porter receives a "Panic" notification, along with the caller number, the
LED stays on until the porter makes contact with the receiver.
The "Panic" notification takes priority over all calls.
Alarm signalling
If an alarm device is connected to the receiver's dedicated input, its activation
will cause an alarm notification to be sent to the porter and this signal will
be notified by the receiver in the form of an intermittent acoustic signal for
approximately 10".
.
DISPOSAL
Do not litter the environment with packing material: make sure it is disposed
of according to the regulations in force in the country where the product is
used. When the equipment reaches the end of its life cycle, take measures
to ensure it is not discarded in the environment. The equipment must be dis-
posed of in compliance with the regulations in force, recycling its component
parts wherever possible. Components that qualify as recyclable waste feature
the relevant symbol and the material's abbreviation.
.
.
on the receiver being called.
on the receiver being called.
to transfer
3