Publicité
Les langues disponibles
Les langues disponibles
EN
3
Recommended Maintenance Schedule
To ensure safe riding, day to day care and regular maintenance are essential. You, the owner, have control and knowledge of
how often you use your scooter, how hard you use it and where you use it. It is the owner's responsibility to perform regular checks
and bring your scooter to authorized service center for inspection and service. Please refer to the maintenance schedule
below.
Note: This maintenance schedule charges a service fee.
Item
Component
Maintenance method
Mainframe parts
Use a soft, wet cloth to wipe the mainframe clean.
Inflate tires to 30–45 psi. Note: Remember to screw
Tire pressure
the valve cap after inflating!
Check if the tires are cracked, deformed, or
Tire wear
significantly worn.
Tighten the six screws fixed with the handlebar and the
stem. The suggested torque is 3 N·m.
Tighten the screw on the throttle. The suggested
Screws on the
Mainframe
torque is 2.5 N·m.
stem top
maintenance
Tighten the screws on the brake levers. The suggested
torque is 13 N·m.
Tighten the screws on the stem top. The suggested
torque is 2.5 N·m.
Tighten the two screws fixed with the front fork and the
folding mechanism. The suggested torque is 15 ± 1 N·m.
Screws on the
If the stem gets shaky when riding, tighen the screw on
folding
the folding mechanism when the scooter is in folded
mechanism
state. The suggested torque is 10 ± 1 N·m.
Brake disc
Tighten the screws on the brake disc assembly. The
assembly
suggested torque is 7.5 N·m.
05
Every 6
After 2 years or
months or
the total
Every 3
every 310
mileage > 3107
months
miles (500
miles (5000
km)
km)
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
Item
Component
Maintenance method
To accelerate and decelerate, check if the hub motor is stalled
Hub motor
or has abnormal sounds.
Rear wheel
Check if the rear wheel is stalled or gets shaky, or the axis shaft
is unbalanced.
maintenance
1) Test method:
Step 1: Squeeze the brake levers, let the brake lever make
contact with the handlebar grip (the distance ≤ 10 mm).
Step 2: Push the scooter, check if the front wheel moves slowly
Brake
forward.
adjustment
2) If the brake is too tight/loose, use the 5 mm Allen key to
loosen the screw on the caliper. Then slightly adjust the brake
line (decrease/increase the exposed length), and tighten the
screw again.
Squeeze brake levers and check if the the brake pads are
Brake pads
significantly worn.
No severe abnormal sounds when riding.
Front and rear
dual trailing
Lift the front and rear wheel off the ground respectively, there
shall no visible swing from up/down or left/right.
Function
arm suspension
Inspection
Spin the wheels, the caliper should be aligned with the rotor and
Brake rotor
they shouldn't rub on the brake pads.
Taillight
Squeeze brake levers, the tail light works normally.
Headlight
Check the headlight and see if it lights brightly.
Dashboard
Power on the scooter, the dashboard works properly.
Horn
Press the horn button, the sound is loud.
Press and hold the throttle then release it, checking for
Throttle
acceleration and deceleration.
Note: Release it, check if the throttle will back to the position.
After connecting with the Segway-Ninebot app:
Fault
1) Update the firmware to the latest version.
detection
2) Check if Energy recovery settings are available.
Charge the scooter:
1) Check if the current battery power displays on the dashboard.
2) Check the color of ambient lights.
Charging
Battery charged status:
Red: 0%-20%. Yellow: 20%-80%. Green: 80%-100%.
EN
Every 6
After 2 years or
months or
the total
Every 3
every 310
mileage > 3107
months
miles (500
miles (5000
km)
km)
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
06
Publicité
