Publicité
Les langues disponibles
Les langues disponibles
1. Remove head from tank and place tank upside down on a flat surface.
2. Place wheels on rear frame/axle assembly with extended hub of wheel
towards dolly frame and
place cap nut on axle.
ITEM
Secure with hammer.
3. Insert caster socket into
1
front frame and secure with
2
phillips head screw.
3
4. Place groove in front frame
4
5
into lip of tank and position
6
so frame is directly
7
above inlet.
8
5. Position grooves of rear
9
frame into lip of tank and
10
11
align so rear and front
frames engage.
6. Secure dolly frame to tank by placing machine screws up through holes in dolly frame.
Ensure head of screw is fully recessed in area provided. After
machine screw is inserted, tighten with flatwasher and hex nut.
7. Insert caster in caster socket and apply downward pressure until caster snaps
into place.
8. Return vacuum to upright position. Attach carriage handle to tank by inserting
bolt through the center hole of
handle and tank, secure with nut
provided. Attach side handles with
screws provided. Be sure to
spread ends of carriage handle
when assembling to prevent dam-
age to tank.
9. Insert basket through center of
carriage handle and slide into
place.
10. Place cap nut on axle. Secure with
hammer.
ITEM
DESCRIPTION
1
Metal tank handle
2
Handle & hardware Pkg.
(includes items 3-6)
3
Side tank handle
4
#10 x 3/4" Screw hex head
5
Bolt 1/4-20 x 1/2"
6
1/4-20 Hex nut
DRY PICK-UP OPERATION
For dry pick-up be sure the opening of the inlet deflector is facing the tank bottom (Figure 1).
With the tank cover in an upside down position, slide the cartridge filter down over the lid
cage, pushing until the filter seals against cover (Figure 2). NOTE: Foam sleeve does not need
to be removed for dry pick-up. Place filter retainer into the top of the cartridge filter, holding
the tank cover with one hand, turn the handle on the filter retainer clockwise to tighten, lock-
ing the filter into place (Figures 3 & 4). To remove the filter for cleaning, again hold the tank
cover and turn the filter retainer counter-clockwise to loosen and remove, slide the cartridge
filter off the lid cage (Figures 5 & 6). To clean the cartridge filter shake or brush off excess
dirt or rinse (from the inside of the filter) with water, dry completely (approximately 24 hours)
and re-install (Figures 7 & 8).
WARNING
– ALWAYS DISCONNECT THE PLUG
FROM THE WALL OUTLET BEFORE REMOVING THE
TANK COVER.
All manuals and user guides at all-guides.com
DESCRIPTION
Cap nut
8" Wheel
Axle
Rear frame
Caster socket
Front frame
#8 x 1/2" lg. Screw
1/4-20 x 3/4" lg. Machine screw
1/4" Flatwasher
1/4-20 Hex nut
Caster
4
6
PART NO.
20882-00
93555-96
93551-00
15039-99
64012-99
13001-99
PART NO.
43002-99
24250-10
24415-00
93921-00
75405-00
93920-00
15015-99
INSTALLING THE DISPOSABLE
09029-99
07003-99
13001-99
67739-00
(Not Standard with All Models)
1. Use for dry pick-up only. Use in conjunction with cartridge filter for picking up
soot, cement, plaster or drywall dust.
2. With cord disconnected from receptacle, pull latches in an outward motion and
remove tank cover.
3. Unscrew hose locking-nut and remove hose from inlet (Figure 9).
4. Remove inlet deflector from deflector guide (Figure 10). NOTE: Hose must be
removed before inlet deflector can be taken out.
5. With the opening of the inlet deflector facing the bottom of the filter bag, slide
1
collection bag collar over deflector matching notches of bag collar to tabs on
inlet deflector, bag will only fit properly one way (Figure 11).
3
6. Slide deflector with collection bag attached into deflector guide (Figure 12).
7. Reinsert hose into inlet and tighten locking-nut (Figure 13).
8. When secured in place, expand bag and position around the inside of tank.
9. Replace tank cover.
9.
5
11.
WET PICK-UP OPERATION
For best results for wet pick-up we recommend removing the cartridge filter and
utilizing the foam sleeve (already in place over the lid cage). For wet pick-up
remove inlet deflector from deflector guide sliding in an upward motion. NOTE:
Hose must be removed before inlet deflector can be taken out. Be sure the open-
ing of the inlet deflector is facing the top of the tank (Figure 14), misting may occur
if inlet deflector is not inserted properly. Misting in exhaust air may occur if the
foam sleeve becomes saturated during wet pick-up. If misting occurs, remove and
dry the saturated foam sleeve or replace with another dry foam sleeve to eliminate
the misting and possible dripping of liquid around the lid. Turn the unit off imme-
diately upon completing a wet pick-up job or when tank is full and ready to be
emptied, raise the hose to drain any excess liquid into the tank. The interior of the
tank should be periodically cleaned.
The foam sleeve should be cleaned periodically as described in the following steps:
1. Always disconnect the plug from wall receptacle before removing the tank
cover. Remove foam sleeve by sliding it up and off the lid cage.
2. Shake excess dust off sleeve with a rapid up and down movement.
3. Hold sleeve under running water rinsing from the inside. A water wash is not
FILTER BAG
10.
12.
13.
Publicité
