Stingray Swing-out Mode D'emploi page 15

ADJUST SEAT DEPTH
The seat depth can be adjusted by slightly loosening two Allen screws (D) (with Allen key 5) and
moving the seat plate up to 7cm. After setting, tighten these two bolts again. The lower flap of the
ADJUST SEAT DEPTH
cushion set is held tight by a strap that runs under the seat and is secured at the rear with a folding
clasp. This will have to be reset
The seat depth can be adjusted by slightly loosening two Allen screws (D) (with Allen key 5) and
moving the seat plate up to 7cm. After setting, tighten these two bolts again. The lower flap of the
cushion set is held tight by a strap that runs under the seat and is secured at the rear with a folding
SEAT WIDTH
clasp. This will have to be reset
The standard seat width of seat size 1 and 2 is 28 cm and of size 3 and 4 it is 38 cm, without the
pelvic supports. You can get a narrower seat width with the adjustable pelvic supports.
SEAT WIDTH
The standard seat width of seat size 1 and 2 is 28 cm and of size 3 and 4 it is 38 cm, without the
TILT ADJUSTMENT
pelvic supports. You can get a narrower seat width with the adjustable pelvic supports.
The seat unit can be adjusted between 10 and 30 degrees by using the clamping lever on the side.
TILT ADJUSTMENT
Footplate
(accessory 8775010+ NLPE046)
The seat unit can be adjusted between 10 and 30 degrees by using the clamping lever on the side.
The footplate is fitted with a mounting rod to the front horizontal frame tube of the Stingray Swing-out
size 3 and 4. The footplate can be folded up and adjusted in angle by the rotary knob on the bottom.
FOOTPLATE Footplate
(accessory 8775010+ NLPE046) (accessory 95145-0 + NLPE046-1)
The height can be adjusted by loosening the Allen screw and adjusting it to the correct height. If the
foot plate is set too high, the turning part will touch the foot plate. The footplate can therefore not be
The footplate is fitted with a mounting rod to the front horizontal frame tube of the Stingray Swing-out
used in this position
size 3 and 4. The footplate can be folded up and adjusted in angle by the rotary knob on the bottom.
The height can be adjusted by loosening the Allen screw and adjusting it to the correct height. If the
foot plate is set too high, the turning part will touch the foot plate. The footplate can therefore not be
ADJUSTABLE/Pelvic Support
used in this position
ADJUSTABLE/Pelvic Support ADJUSTABLE PELVIC SUPPORT
The standard hip supports have three possible
width options.
They can be adjusted by the addition and removal
of the bolt and spacers.
The standard hip supports have three possible
The adjustable hip supports use flip up levers to
width options.
give greater adjustment possibilities.
They can be adjusted by the addition and removal
Always ensure that the car seat belt runs over the
of the bolt and spacers.
users hips and not over the hip supports.
The adjustable hip supports use flip up levers to
give greater adjustment possibilities.
Always ensure that the car seat belt runs over the
users hips and not over the hip supports.
12 Transportation | Stingray Swing-out
28 Transportation | Stingray Swing-out
12 Transportation | Stingray Swing-out
(accessory 87202xx)
(accessory 87202xx) (accessory 87402XX)
Junior | Transportation
Junior | Transportation
SIDE IMPACT HEADREST ~
The Side Impact headrest (SI) can be adjusted in total by approximately 10 cm in height.
Loosen two bolts (G) (with Allen key 6) and slide the SI headrest. Optionally, the mounting plate can
still be moved in height by loosening the 4 bolts (H) and moving the mounting plate one step higher.
This causes the SI headrest to rise above the seat.
ANATOMICAL NECK CUSHION
As an additional support, the Side-Impact headrest can be fitted with an anatomical neck cushion with
folding clasps that provide additional support for the child's head and neck
SIDE SUPPORTS
(NLPE040/041)
The side supports (I) are placed in the slots in the
clamp levers on the backrest.
OUTER KNEE SUPPORTS
(NLPE043/044)
The outer knee supports are fitted on the outside
knee supports are provided with a cover.
REAR SEAT PROTECTION
(NLPE011)
I.C.M. PROTECTION PILLOWS
The rear seat protector and protective pads are used to protect the rear seat. Place the protective
cushions on the rear seat (backrest and seat) and the rear seat protector on the outside of the
protective cushion. The end of the plate is level with the side of the rear seat. For example, the back
seat is protected when the car seat is extended.
(standard)
(8720831)
backrest. Then fix the side supports using the
of the seat plate by means of two bolts (J). These
(NLSW071) (NLSW071/NLSW070)
Transportation| Stingray Swing-out
Transportation | Stingray Swing-out
UK
29
13