Ego Power+ BAX1500 Mode D'emploi page 8

1. Connect the charger to the power supply
EN
(220-240V~50Hz).
2. Insert the battery plug into the charger.
3. If the battery pack is in the normal charging, the
green LED1 on the charger will flash. After green
button-pressing for at least 1s, the normal charging
(charging current 4A) will transform to rapid
(charging current 8A) and green LED2 on the charger
will flash with LED1 off.
4. 5 LEDs of battery pack shining green continuously
means the battery pack is fully charged. Wait until the
cooling fan of the charger stops, remove the battery
pack from the charger and disconnect the charger
from power supply.
NOTICE:
◾
The battery pack will fully charge if left on the charger,
but it will not overcharge.
◾
Following the instructions in the Operator's Manual for
the EGO CHX5500E charger for more details.
◾
A significantly reduced running after fully charging the
battery pack indicates that the batteries are near the
end of their usable life and must be replaced.
◾
If you have not inserted the plug into its place
completely, LED of charger light would flash continually.
◾
The charger may warm during charging. This is part of
the normal operation of the charger. Charge in a well-
ventilated area.
USB/12V DC
Uncover the rubber covers and insert the USB/DC plugs
into USB/DC ports (Fig. C & D). Then press the USB/DC
switch button, the battery pack will connect the devices
via USB or DC ports.
C-1 Rubber Covers
D-1 USB Port
NOTICE:
◾
The functions of USB and 12V DC power can work
with 56V power source simultaneously. After using of
USB/12V DC, pull out the USB/DC plugs and put the
rubber covers into its place.
◾
Should not use the USB/12V DC while the battery pack
is charging.
8
56-VOLT BACKPACK BATTERY — BAX1500
All manuals and user guides at all-guides.com
CONNECT AND DISCONNECT HARNESS TO/FROM
BATTERY PACK
To Connect
Align the four location ribs on the frame with the mounting
grooves and connect the location slot on the belt with the
belt fixation spring. Then slide the harness up until a click
charging
happening. (fig.E).
To Disconnect
Press the two release buttons on harness behind the frame
and slide the harness out (Fig. F).
PUT ON THE BATTERY PACK
In normal operation, the battery pack with the harness
is worn on the back. To prevent fatigue and work
comfortably, the harness is equipped with a belt joint
and shoulder strap joints, which guarantees freedom of
movement.
The belt length of the lap belt and shoulder straps can
be adjusted freely. The back cushion should fit firmly and
securely on your back.
◾
◾
◾
◾
◾
D-2 12V DC Port
D-3 USB/DC Switch
TO ATTACH AND DETACH THE BATTERY PACK
Charge before first use
Guide the battery pack cable around the side of the body,
and connect the power tools to the 1.5m connection cable.
Follow the instructions in the power tools' manual for the
futher details.
To Install (Fig. K)
With aligned ▲ logo respectively on the plug and the
power tools, insert the plug into the power tools until the
green seal completely disappearing into the socket.
To Remove
Pull the plug out of the power tools.
E-1 Mounting Groove E-3
E-2 Frame Location rib
Adjust the belt and shoulder strap length to make
yourself comfortable before normal work, the length
should fit your body size through the lap belt and
shoulder strap joint.
Insert the two parts of the belt buckle and chest buckle
into each other until a click occurs (Fig. G & H).
Adjust the height of the chest buckle to make yourself
comfortable (Fig. I).
Readjust the length of the belt strap and chest strap.
Insert any extra length of belt around the waist and
chest strap into the elastic (Fig. J).
Belt location slot