Ingersoll Rand powerforce PF900 Manuel D'utilisation Et D'entretien

OPERATION AND MAINTENANCE MANUAL
FOR PF900 AIR POWERED GREASE GUN
Model PF900 Grease Gun is designed for injecting grease into grease fittings for home use.
IMPORTANT SAFETY INFORMATION ENCLOSED - - SAVE THESE INSTRUCTIONS
READ AND UNDERSTAND THIS MANUAL BEFORE OPERATING THIS PRODUCT
IT IS YOUR RESPONSIBILITY TO MAKE THIS SAFETY INFORMATION
AVAILABLE TO OTHERS THAT WILL OPERATE THIS PRODUCT
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD
Always install, operate, inspect and maintain this
•
product in accordance with all applicable standards
and regulations (local, state, country, federal, etc.).
Always use clean, dry air at 90 psig (6.2 bar/620 kPa)
•
maximum air pressure at the inlet. Higher pressure
may result in hazardous situations including excessive
speed, rupture, or incorrect output torque or force.
Be sure all hoses and fittings are the correct size and
•
are tightly secured. See Dwg. TPD905- - 2 for a typical
piping arrangement.
Ensure an accessible emergency shut off valve has
•
been installed in the air supply line, and make others
aware of its location.
Always wear eye protection when operating or
•
performing maintenance on this tool.
Always use Personal Protective Equipment
•
appropriate to the tool used and material worked.
This may include dust mask or other breathing
apparatus, safety glasses, ear plugs, gloves, apron,
safety shoes, hard hat and other equipment.
This tool is not designed for working in explosive
•
environments, including those caused by fumes and
dust, or near flammable materials.
This tool is not insulated against electric shock.
•
Power tools can vibrate in use. Vibration, repetitive
•
motions or uncomfortable positions may be harmful
to your hands and arms. Stop using any tool if
discomfort, tingling feeling or pain occurs. Seek
medical advice before resuming use.
The use of other than genuine Powerforce by Ingersoll- - Rand replacement parts may result in safety hazards, decreased
tool performance, and increased maintenance, and may invalidate all warranties.
Repairs should be made only by an authorized Powerforce Servicenter. Call toll free 1 (866) 207-6923.
Refer all communications to the nearest Ingersoll- - Rand
Office or Distributor
 Ingersoll- - Rand Company 2002
Printed in Taiwan, R.O.C.
All manuals and user guides at all-guides.com
CAUTION NOTICE
RESULT IN INJURY
PLACING TOOL IN SERVICE
•
•
•
•
•
•
USING THE TOOL
•
•
•
•
•
•
•
•
•
04579231
Form P7603
Edition 1
November, 2002
Do not use damaged, frayed or deteriorated air hoses
and fittings.
Keep clear of whipping air hoses. Shut off the
compressed air before approaching the whipping
hose.
Always turn off the air supply and disconnect the air
supply hose before installing, removing or adjusting
any accessory on this tool, or before performing any
maintenance on this tool.
Do not lubricate tools with flammable or volatile
liquids such as kerosene, diesel or jet fuel. Use only
recommended lubricants.
Keep work area clean, uncluttered, ventilated and
illuminated.
Do not remove any labels. Replace any damaged label.
Keep body stance balanced and firm. Do not
overreach when operating this tool. Anticipate and be
alert for sudden changes in motion, reaction torques,
or forces during start up and operation.
To avoid accidental starting - - ensure tool is in "off"
position before applying air pressure, avoid throttle
when carrying, and release throttle with loss of air.
Ensure work pieces are secure. Use clamps or vises to
hold work piece whenever possible.
Do not carry or drag the tool by the hose.
Do not use power tools when tired, or under the
influence of medication, drugs, or alcohol.
Never use a damaged or malfunctioning tool or
accessory.
Do not modify the tool, safety devices, or accessories.
Do not use this tool for purposes other than those
recommended.
Use accessories recommended for PowerForce by
Ingersoll- - Rand.
US
F
E