STEINEL XSolar SOL-O Sensor Mode D'emploi page 11

GB
1� About this document
Please read carefully and keep in a safe place�
– Under copyright. Reproduction either in whole or in part
only with our consent.
– Subject to change in the interest of technical progress.
– All product dimensions in mm.
Symbols
!
Hazard warning!
Reference to other information in the
document�
...
2� General safety precautions
• Only use genuine replacement parts.
• Repairs may only be made by specialist
!
workshops.
Hazard from vapours or electrolyte fluid!
Vapours or electrolyte fluid may escape from the recharge-
able battery if it is damaged or used improperly. Coming
into contact with them may result in severe injury ( e.g. loss
of sight, acid burns ).
• Never open the rechargeable battery enclosure or the
rechargeable battery itself.
• Do not allow vapours or electrolyte fluid to come into
contact with your eyes. In the event of contact with
eyes:
– Do not rub your eyes.
– Immediately rinse eyes with plenty of clean water
( such as tap water ).
– Seek medical advice.
• Do not touch any electrolyte fluid that has escaped.
• Immediately move product away from naked flamed or
sources of heat.
• Immediately remove contaminated clothing.
• The light source of this luminaire cannot be replaced.
If the light source needs to be replaced ( e.g. at the
end of its service life ), the complete luminaire must be
replaced.
3. XSolar SOL-O S / XSolar
SOL-O / XSolar SOL-O HN
Proper use
– Solar light with LEDs as the light source, for mounting
on outdoor walls.
Solar lights provide illumination in places where there is
no mains power supply. The solar panel and rechargeable
battery provide an independent supply of energy.
– XSolar SOL-O S detects movement via an integrated
infrared sensor and switches light ON.
– XSolar SOL-O automatically detects when it is dark
and switches light ON.
110073820_STE_XSolar SOL-O S_SOL-O_HN.indd 11 110073820_STE_XSolar SOL-O S_SOL-O_HN.indd 11
– XSolar SOL-O HN automatically detects when it is
dark and switches light ON. Integrated ilIuminated
house number
Package contents (Fig� 3�1 )
– Solar light with wall mount
– 2 screws
– 2 wall plugs
– 2 shrouds for restricting the detection zone (only with
XSolar SOL-O S)
Product dimensions, XSolar SOL-O S (Fig� 3�2)
Product dimensions, XSolar SOL-O (Fig� 3�3)
Product dimensions, XSolar SOL-O HN (Fig� 3�4)
Product components, XSolar SOL-O S (Fig� 3�5)
A Solar panel
B Wall mount
C Micro USB charging socket
D Rubber seal
E Programme selector switch
F Catch
G Sensor unit
Product components, XSolar SOL-O (Fig� 3�6)
Solar panel
A
B Wall mount
C Micro USB charging socket
D Rubber seal
E Programme selector switch
F Catch
Product components, XSolar SOL-O HN (Fig� 3�7)
A Solar panel
B Wall mount with illuminated panel for the house
number (HN)
C Micro USB charging socket
D Rubber seal
E Programme selector switch
Catch
F
Detection zone (XSolar SOL-O S): max. 6 m (Fig� 3�8)
4� Mounting
• Check all components for damage.
• Do not use the product if the solar panel or LED panel
is damaged.
• Choose an appropriate site with plenty of sunlight for
installing the solar panel (facing south).
• Avoid shade from porches, overhanging roofs or trees.
• Pay attention to detection reach.
• Peel film off solar panel.
Note:
We recommended fully charging the solar light's
rechargeable battery before the first time of use
➔ "6� Charging the battery manually"
Performance will be limited if the product is used in adverse
conditions (e.g. installed in shade or behind glass)
- 11 -
GB
06.11.23 16:40 06.11.23 16:40