Product And Package Contents; Preliminary Warning Notices; Initial Operations, Safety Instructions; Working On The Device - Laserworld Ecoline Série Mode D'emploi

1. Product and package contents

Please check if all listed parts are included and undamaged. Included in delivery:
1 x laser projector
1 x remote control unit

2. Preliminary warning notices

Please use this device only according to these operating instructions.
1.
Do not use the device if there are any visible damages on housing, connector
2.
panels, power supplies or power cords.
3. Never look directly into the light source of a laser projector. Danger of dama-
ge to the eyes or even blindness in extreme circumstances!
Do not operate the device at high humidity, in the rain or in dusty
4.
environments.
Protect device against dripping or splashing water. Do not place
5.
any liquid filled containers near to this device.
Any warranty claims are void if the warranty label is removed or tampered
with in any way.

3. Initial operations, safety instructions

1. Make sure to use correct voltage;
see information on device & in this
manual.
Make sure that the device is not
2.
connected to mains during ins-
tallation.
3. Installation has to be done by
technical experienced and qua-
lified persons according to safe-
ty regulations of the respective
country.
4. Always ensure that maximum
permissible exposure (MPE) is
not exceeded in areas accessib-
le to the public or members of
staff.
5. In some countries an additional
inspection by technical control
institutes could be necessary.
1 x manual 1 x PSU
1 x mini tripod
6. Connect an easily accessible inter-
lock connector or circuit breaker
to the projector.
7. The power supply should be easily
accessible.
8. If the device has been exposed to
great temperature changes, do
not switch it on immediately. Con-
densation (or any moisture/water
formed) may damage device.
9. Never use dimmer, RC or other
electronically switched sockets.
Whenever possible, do not use the
laser projector together with large
appliances (especially fog machi-
nes) on the same mains!
10. Ensure sufficient ventilation and
do not place the device on any
warm or heat radiating surface. Es-
pecially the ventilation openings
must not be covered!
11. Ensure that device does not get
overheated. Make sure that the

4. Working on the device

1. Be sure that the mains plug is not connected to the power supply while
installing.
2. Take off all reflecting things like rings, watches etc. before starting to work
with or at the projector.
3. Only use non-reflecting tools to work on device.
4. Wear protective clothing (like goggles, gloves etc.) according to laser power
and wavelength of the laser.

5. Service notes

• Moisture and heat can reduce
lifetime of the laser system dra-
matically and expires any warranty
claim.
• Quick on/off switching of this de-
vice will reduce durability of the
laser diode dramatically.
• Avoid sharp knocks and shocks to
this device and ensure sufficient
protection during transportation.
Look after your Laserworld pro-
duct.
• To increase durability of your
laser, protect device against
overheating:
-
Always ensure sufficient ventila-
tion.
-
Do not face spotlights (especially
moving heads) to the device.
-
Check temperature after approx.
30 minutes with each new ins-
tallation. If necessary install the
projector at a place with different
temperature.
- Keep the device dry. Protect it
device is not exposed to spotlights
(especially moving heads). Heat of
spotlights could overheat laser in
a little while and leads to a degra-
dation of performance.
from moisture, rain and damp.
-
Switch off device when it is not
needed. Diodes are switched on
and can wear out even if there is
no visible laser output.
• The devices of Ecoline, Evolution,
Club and Proline Series are not
meant for professional applica-
tions. After approx. one hour of
operation, the device should cool
down for about 15 minutes.
• Please ensure the fans and hea-
tsinks are clear from dust and
debris otherwise the risk of over-
heating may occur. If the unit and
airways appear to be blocked then
please contact a qualified service
engineer to maintain and service
the product.
• Removal of the warranty label
as well as damages to the device
caused by improper handling,
neglect of the safety instruc-
tions and service notes will void
the warranty.