Timex W193-NA Mode D'emploi

THANK YOU FOR PURCHASING YOUR TIMEX® WATCH.
Please read these instructions carefully and save for future reference.
Your watch may not have all of the features described below.
• IRONMAN TRIATHLON® watch with dual tech feature. This new feature provides you with
the option to turn off the digital display providing a clean analog look.
• Time and Date: Analog and digital time display • 12/24-hour digital time formats • Day-
Month or Month-Day date format • 2 time zones • Hide digital display
• Chronograph: Time 100 laps and store 50
• Countdown Timer: 24-hour countdown timer with repeat
• Alarm: Daily, weekday or weekend settings • Backup alarm
• Optional Hourly Chime
• INDIGLO® night-light: Illuminates watch display for 3-4 seconds
• NIGHT-MODE®: When activated allows you to turn on Indiglo by pressing any button.
Select functions by repeatedly pressing the MODE button to cycle through TIME, CHRONO-
GRAPH, TIMER, and ALARM modes. In any mode, you can view the time by pressing the
MODE button. Symbols appear in the display to indicate what functions are active.
In each mode, press SET/RECALL to change values. Button functions change when setting
your watch. The watch face displays the new functions. Press SET/RECALL (Done) to exit and
return to the active mode.
Pressing the INDIGLO® night-light button illuminates your watch face for viewing the dis-
play in low light. When in NIGHT-MODE® feature, pressing any button will illuminate watch
display for 3-4 seconds
The INDIGLO® night-light flashes and a melody plays whenever an alert occurs, such as at
end of a countdown. Press any button to stop the alert.
SET/RECALL
(Done)
MODE
(Next)
Items in ( ) appear in display only while setting.
+ –
TIP : Hold or to change values rapidly.
Pull crown and turn to set HOUR and MINUTE hands.
DIGITAL TIME AND DATE, HOURLY CHIME, BUTTON BEEP
To turn the digital display on/off, press and hold STOP/RESET.
A. To set the time and date display, press and hold SET/RECALL. Press
ZONE 1 or 2 to set.
B. Press NEXT repeatedly to select, in sequence, HOURS, MINUTES, MONTH, DATE, time
format (12-hour or 24-hour), date format (day-month or month-day), HOURLY CHIME
(on/off) and BUTTON BEEP (on/off).
C. To change the values, press
To select AM or PM, advance HOURS digits through 12-hours (12-hour display format).
D. After setting the first Time Zone, select the other Time Zone and repeat the procedure to
set the time for that zone.
E. Press DONE at any time to finish setting.
To view the other time zone, press START/SPLIT. Press and hold the button to change
display to the second time zone.
CHRONOGRAPH — COUNT AND STORE YOUR LAPS/SPLITS
A. To operate the Chronograph, press MODE repeatedly until CHRONO appears.
B. Press START/SPLIT to start the Chronograph. Press again to take lap/split time. The
primary display shows both the lap/split time for 10 seconds or until the MODE button is
pressed.
C. Press STOP/RESET to stop timing. Press START/SPLIT to resume.
D. To recall your stored lap/split times while the Chrono is stopped or running, press
SET/RECALL and then
E. Press NEXT and
DONE to exit.
F. While the Chrono is stopped, press and hold STOP/RESET to reset the Chrono.
Chronograph continues to run if you exit mode. Stopwatch icon
A. To operate the Timer, press MODE repeatedly until TIMER appears. Press NEXT to select
HOURS, MINUTES, SECONDS and STOP or REPEAT AT END. Press
Press DONE to exit.
B. To set the timer, press and hold SET/RECALL. Timer must be stopped.
C. Press START/SPLIT to begin timing, STOP/RESET to stop, START/SPLIT to resume.
D. With the TIMER stopped, press STOP/RESET to reset the Timer to the beginning of the
countdown time.
Register your product at
www.timex.com
W193-NA
BASIC OPERATIONS — HOW YOUR WATCH WORKS
+ –
/ repeatedly. Pressing
+ –
/ repeatedly.
+ –
/ to change display format between LAP/SPLIT and SPLIT/LAP. Press
COUNTDOWN TIMER
127-095000 Rev.02
FEATURES
ANALOG TIME
+
INDIGLO® NIGHT-LIGHT
STOP/RESET
–
(decrease value)
START/SPLIT
+
(increase value)
+ –
/ to select TIME
–
/ will set SECONDS to zero.
appears in Time mode.
+ –
/ to change settings.