Machine-Specific Safety Warnings; Functional Description - stayer DM1450 Instructions D'emploi

This manual is consistent with the date of manufac-
ture of your machine, you will find information on
the technical data of the machine acquired manual
check for updates of our machines on the website:
www.grupostayer.com
Machine-specific
Safety Warnings
- Do not use the power tool for explosive materials
(e. g, easily inflammable solvents). Power tools pro-
duce sparks which could ignite developing vapours.
- In case the power tool should fall into the material
to be stirred, pull the plug immediately and have
the power tool checked by an after-sales service
agent. Material that has penetrated the power tool
can cause damage and lead to an electric shock.
- Always use the auxiliary handle supplied with the
machine. Loss of control can cause personal injury.
- When working with the machine, always hold it fir-
mly with both hands and provide for a secure stan-
ce. The power tool is guided more secure with both
hands.
- Do not work materials containing asbestos. Asbes-
tos is considered carcinogenic.
- Take protective measures when dust can develop
during working that is harmful to one's health,
combustible or explosive. Example: Some dusts
are regarded as carcinogenic. Wear a dust mask and
work with dust/chip extraction when connectable.
- Always wait until the machine has come to a com-
plete stop before placing it down. The tool insert
can jam and lead to loss of control over the power tool.
- Never use the machine with a damaged cable. Do
not touch the damaged cable and pull the mains
plug when the cable is damaged while working.
Damaged cables increase the risk of an electric shock.
- Connect machines that are used in the open via a
residual current device (RC D).

Functional Description

Read all safety warnings and all instruc-
tions. Failure to follow the warnings and ins-
tructions may result in electric shock, fire and/or
serious injury.
While reading the operating instructions, unfold the gra-
phics page for the machine and leave it open.
Utilización reglamentaria
La herramienta eléctrica ha sido diseñada para remover
materiales de construcción en polvo como morteros,
revoques, adhesivos y pinturas, lacas o demás sustancias
similares que también estén exentas de disolvente.
ENGLISH
10
The values given are valid for nominal voltages [U] of
230/240 V ~ 50/60 Hz - 110/120 V ~ 60 Hz. For lower
voltage and models for specific countries, these values
can vary.
Please observe the article number on the type pl ate of
your machine. The trade names of the individual machi-
nes may vary.Product Features
The numbering of the product features refers to the illus-
tration of the machine on the graphics page.
1. Mechanical velocity selector.
2. Auxiliary handle.
3. Propeller stirrer
4. Spindle motor.
5. Switch on / off.
6. Locking key switch on / off.
7. Speed adjustment.
Noise/Vibration Information
Measured values determined according to EN 60745 Typi-
cally the A-weighted noise level of the machine is: sound
pressure level 87 dB(A); sound power level 98 dB (A). Un-
certainty K=3 dB.
Wear hearing protection!
The typical hand/arm vibration is below 2.5 m2/s
WARNING
accordance with a standardised test given in EN 60745 and
may be used to compare one tool with another.
The vibration emission level will vary because of the ways in
which a power tool can be used and may increase above the
level given in this information sheet.
This could lead to a significant underestimate of exposure
when the tool is used regularly in such a way.
Note: To be accurate, an estimation of the level of ex-
posure to vibration experienced during a given period of
work should also take into account the times when the
tool is switched off and when it is running but not actually
doing the job. This may significantly reduce the exposure
level over the total working period.
Assembly
Before any work on the machine itself, pull the
mains plug.
Changing the Tool
Stirrer Paddle with Male Thread, Size M14/M18 (Mod DM1450)
EScrew the stirrer paddle 3 onto the drive spindle 4
Hold the drive spindle 4 in place with an open-end
spanner (size 22 mm ) and the stirrer paddle 3
with a second open-end spanner (size 22 mm).
The stirrer paddle is disassembled in reverse order.
Operation
10
The vibration emission level given in this
information sheet has been measured in