Milwaukee PD2-20 Instructions D'utilisation page 2

Introduction
Technical Data
Advice for your
safety
Measured sound
value
Measured
vibration value
Mains
connection
Use
ENGLISH
All manuals and user guides at all-guides.com
You are demanding and expect to purchase quality goods – quality offered by
Milwaukee. We have built a durable and reliable electric power tool for you.
Please read the instructions for use before first operation so you can handle your power
tool effectively and safely. We are sure that buying an Electric Power Tool from
Milwaukee was the right choice!
Nominal power . . . . . . . . . . . . . . . . .
No-load speed
1st gear . . . . . . . . . . . . . . . . . . . .
2nd gear . . . . . . . . . . . . . . . . . . . .
Speed under load max.
1st gear . . . . . . . . . . . . . . . . . . . . .
2nd gear . . . . . . . . . . . . . . . . . . . .
Rate of percussion under
load max. . . . . . . . . . . . . . . . . . . .
Drilling capacity in
Concrete . . . . . . . . . . . . . . . . . . . . . .
Brick and tile . . . . . . . . . . . . . . . . . .
Steel . . . . . . . . . . . . . . . . . . . . . . . . .
Wood . . . . . . . . . . . . . . . . . . . . . . . .
Drill opening range
Drive shank . . . . . . . . . . . . . . . . .
Chuck neck diameter
Weight . . . . . . . . . . . . . . . . . . . . . . . . .
The data stated above apply for models with 230 – 240 V. In case of deviating
mains voltage, the data stated on the rating plate are applicable.
J Please pay attention to the safety instructions in the attached leaflet!
J Dust that arises when working on material containing asbestos or stonework
containing crystalline silicic acid is harmful to the health. Please follow accident
prevention regulations.
J Appliances used at many different locations including open air must be connected
via a current surge preventing switch.
J Always wear goggles when using the machine. It is recommended to wear gloves,
sturdy non slipping shoes and apron.
J Sawdust and splinters must not be removed while the machine is running.
J Do not pierce the motor housing as this could damage the double insulation (use
adhesives).
J Always disconnect the plug from the socket before carrying out any work on the
machine.
Only plug-in when machine is switched off.
J Keep mains lead clear from working range of the machine. Always lead the cable
away behind you.
J Always use the auxiliary handle.
J Do not use diamond core drills on hammer mode.
J When drilling in walls ceiling, or floor, take care to avoid electric cables and gas or
waterpipes.
Typically the A-weighted noise levels of the tool are:
Sound pressure level = 103 dB (A). Sound power level = 116 dB (A). Wear ear
protectors! Measured values determined according to EN 50 144.
Typically the weighted acceleration is 9 m/s
Measured values determined according to EN 50 144.
Connect only to a single-phase AC current supply and only to the mains voltage
specified on the rating plate. Connection to sockets without earth protection is
possible as the appliance features protective insulation to DIN 57 740/ VDE 0740
and CEE 20. Radio suppression complies with the European standard EN 55014.
When fitting the plug, make sure that the brown (live) wire of this appliance is
connected to the plug terminal marked L or coloured red, and the blue (neutral) wire
of this appliance is connected to the plug terminal marked N or coloured black.
Under no circumstances must the wires of this appliance be connected to the earth
terminal of the plug marked either E, with the earth symbol or coloured green or
green/yellow.
The electronic drill/screwdriver can be universally used for drilling, percussion drilling,
screwdriving and cutting screw threads.
Do not use this product in another way as stated for normal use.
1
PD2-20
705 W
1350 min
3200 min
750 min
1850 min
36000 min
20 mm
20 mm
13 mm
40 mm
. . . . . . . . . . . . 3–16 mm
1/2"x20
. . . . . . . . . . . . 43 mm
2,2 kg
PD2E 20 R
. . . . . . . . . . . . . 705 W
-1
. . . . . . . 0–1350 min
-1
. . . . . . . 0–3200 min
-1
. . . . . . . . 0–750 min
-1
. . . . . . . 0–1850 min
-1
. . . . . . . . 36000 min
. . . . . . . . . . . . . 20 mm
. . . . . . . . . . . . . 20 mm
. . . . . . . . . . . . . 13 mm
. . . . . . . . . . . . . 40 mm
. . . . . . . . . 1,5–13 mm
. . . . . . . . . . . 1/2"x20
. . . . . . . . . . . . . 43 mm
. . . . . . . . . . . . . 2,2 kg
2
.
PD2-20, PD2E 20 R
-1
-1
-1
-1
-1