S&P HXBR Mode D'emploi page 7

INPUT REGISTERS (read only) continuation
Modbus Input register
Address
30019 OverVoltage_Alarm_Count 16bits 0-65535 -
30020 ShortCircuit_Alarm_Count 16bits 0-65535 -
30021 Current_Alarm_Count
30022 TempPCB_Alarm_Count
30023 TempIPM_Alarm_Count
30024 FOC_Alarm_Count
30025 OpenPhase_Alarm_Count
30026 Minutos_ON
30027 Days_ON
30028 Minuts_Running
30029 Days_Running
30030 MSB_Motor_Start_Count
30031 LSB_Motor_Start_Count
HOLDING REGISTERS (read and edit)
Modbus Holding register
Address
40002 Address
40003 Baud Rate
40004 Parity
40005 Motor_Max_Speed
40006 Motor_Min_Speed
40007 Motor_Max_Cu-
rrent
40008 FG
40009 Slave_Enable
40010 Slave_Offset
40011 AN_IN1_1V/5.5mA
40012 AN_IN1_9.5V/19mA 16bits -64000
40013 AN_IN1_Filter
40014 AN_IN2_0V/4mA
40015 AN_IN2_10V/20mA
40016 AN_IN2_Filter
40018 Set_Point_Input
40019 Modbus_Set_Point
40025 Factory_Reset
MODBUS MAP
Data Range Def. Observations
type
16bits 0-65535 -
16bits 0-65535 -
16bits 0-65535 -
16bits 0-65535 -
16bits 0-65535 -
16bits 0-1440 -
16bits 0-65535 -
16bits 0-1440 -
16bits 0-65535 -
16bits 0-65535 -
16bits 0-65535 -
Data Range Default
type
16bits 1-247 1
16bits 48: 4800 192
96: 9600
192: 19200
384: 38400
16bits 0: EVEN 0
1: ODD
2: Non parity
16bits 0-5000 Ex-factory
maximum
speed
16bits 0-5000 Ex-factory
minimum
speed
16bits 0-10000 Ex-factory
maximum
intensity
16bits 0-10 1
16bits 0: OFF 1
1: ON
16bits -20-20 0
16bits -64000 Ex-factory
maximum
speed
Ex-factory
minimum
speed
16bits 0: EVEN 1
1: LOW
2: MEDIUM
3: HIGH
16bits -64000 0
16bits -64000 0
16bits 0: EVEN 1
1: LOW
2: MEDIUM
3: HIGH
16bits 0: AN_IN1 0
1: MODBUS
16bits 0-65535 0
16bits -64000 0
(continuation)
Overvoltage alarm counter
Short circuit alarm counter
Motor current alarm counter
PCB temperature alarm counter
IPM temperature alarm counter
FOC control alarm counter
Motor phase error alarm counter
Minutes operation of powered motor
Days operation of powered motor
Minutes operation with motor running
Days operation with motor running
Motor starts MSB
Example: MSB = 2 = 2 x 65,535 = 131,070 starts + LSB
Motor starts LSB
Example: LSB = 1000 = 1,000 starts + MSB
Observations
Modbus Channel/Direction
Bus speed
Parity
Maximum motor speed. Values outside the ex-factory limits or
lower than Holding register 40006 are not accepted
Minimum motor speed. Values outside the ex-factory limits or
higher than Holding register 40005 are not accepted
Maximum motor intensity (mA), doesn't accept values higher
than the ex-factory limit
Tachometer pulses
Slave function to control a second fan
Offset of the slave setpoint with respect to the setpoint (%)
Equivalence in real units of 1V or 5.5mA with respect to input IN1
Note: Only used for constant power, constant torque, PI, Proportio-
nal and Min/Max operating modes
Equivalence in real units of 9.5V or 19mA with respect to input
IN1
Note: Only used for constant power, constant torque, PI, Proportio-
nal and Min/Max operating modes
Degree of fi ltration of input IN1. A high degree favours progres-
sive changes in fan speed
Equivalence in real units of 0V or 4mA with respect to input IN2
Equivalence in real units of 10V or 20mA with respect to input
IN2
Degree of fi ltration of input IN2. A high degree favours progres-
sive changes in fan speed
Setpoint control
Setpoint via Modbus, units according to Holding register 40017
operating mode
Note: If holding registers 40011 and 40012 are not completed, the
units will be mV
Write 1234 to reset motor and return to factory settings
Note: By factory values we mean the limits corresponding to the maxi-
mum performances, constant speed operating mode and adjustment
via IN1. If the unit came with a special confi guration, this will be lost
7