RugDoctor Might PRO X3 Mode D'emploi page 6

Before You Begin
Review machine safety warnings found in
(ILLUS.1)
the front of this manual. Using a normal
dry vacuum cleaner, vacuum the area you
want to clean to remove loose dirt before
using the Rug Doctor machine. This will help
keep the brushes and water vacuum system
working efficiently. Pre-treat any special
problem areas with appropriate Rug Doctor
(ILLUS.2)
solutions. For example, use Urine Eliminator
on tough pet stains and other bio-origin
stains.
Set Up
Check the back of the machine to ensure
(ILLUS.3)
hose connections are secure and set to
clean carpet instead of upholstery (ILLUS.1)
Lift up on the recovery latch and raise dome
hood (ILLUS.2). Remove the recovery tank.
Depending on how dirty your carpets are,
add 2oz- 4oz (1/4 to 1/2) cup of Rug Doctor
Oxy-Steam
(ILLUS.4)
gallon of hot tap water in a clean bucket
(ILLUS.3). Use caution to insure water is not
so hot as to scald or burn skin.
The lower tank effective capacity for the
Rug Doctor Mighty Pro X3™ is 1.9 gallons.
Fill the lower tank with the Rug Doctor
(ILLUS.5)
Oxy-Steam
through the white filter screen. Machine
is full when liquid halfway covers the filter
screen (ILLUS.4). If foaming occurs, add 1
to 2 oz. of Rug Doctor Anti-Foam to recovery
tank (ILLUS.5). Replace recovery tank and
close the dome hood (ILLUS.2).
(ILLUS.6)
Plug in the power cord and position the
machine. Refer to the label on the side of
the handle. Slide the switch to the "Carpet"
position for carpet cleaning (ILLUS.6).
(ILLUS.7)
tool / 0 /carpet "0" is off position
reset button is located below
(ILLUS.8)
recovery latch
& dome hood
recovery tank
(ILLUS.9)
(ILLUS.10)
6
All manuals and user guides at all-guides.com
Cleaning Carpets
Carpet Cleaner product per
®
Cleaning solution by pouring
®
press for spray
To learn more about how to clean your carpets,
refer to "Using your Rug Doctor" section on www.rugdoctor.com
Start Cleaning
While depressing the press for spray red
button on the top of the handle (ILLUS.7), pull
the machine slowly and steadily backward in
a straight line, keeping vacuum slot against
the carpet surface. You will begin to see soiled
solution entering the clear dome. (If you don't,
stop and refer to the Troubleshooting section).
IMPORTANT: When depressing the press for
spray red button, keep machine moving so the
vibrating brush does not agitate in one place
(ILLUS.8).
Release the red button 6 to 12 inches before
ending each pass to stop cleaning solution. Tilt
machine back and push it forward to start a new
backward cleaning pass (ILLUS.9).
Our machines are designed to clean in one pass;
however, 2 passes may be made over the same
area if your carpet is heavily soiled. (Unless it is
a Berber, Multi-Level or Looped carpet, in which
case only 1 pass should be used).
Continue cleaning in this manner, overlapping
each pass slightly. When the lower tank runs
out of cleaning solution, the pump sound will
increase in volume slightly and dirty water will
stop entering the dome. Switch the machine to
"0" for the off position. Remove and empty the
recovery tank by pouring dirty solution into a
toilet or outdoors (ILLUS.10).
Rinse the recovery tank and refill the lower tank
with clean solution/water mixture using a clean
bucket. If you are near the end of your cleaning
job, fill the lower tank half full so it empties by
the end of your job. Replace the recovery tank.
Continue the cleaning process until area to be
cleaned is covered. When cleaning is complete,
switch the machine to "0" for the off position. To
drain and clean the machine, please refer to the
Maintaining Your Rug Doctor Machine section.
handle release
dome filter
lower tank
vacuum slot
(bottom edge
of machine)