SAMES KREMLIN 40C50 AIRLESS Notice Originale page 16

POMPE MURALE, modèle 40C50
sans filtre, sans canne d'aspiration
WANDANLAGE, Modell 40C50
ohne Filter, ohne Saugschlauch
Ind #
- 151 775 000 Pompe 40C50 nue
 Moteur 1000-4
*1 146 275 000
(voir Doc. 573.045.050)
 Hydraulique C50
*2 144 950 000
(voir Doc. 573.032.050)
 Tirant
3 051 770 001
 Ecrou HM 10
4 953 010 021
 Rondelle MN 10
5 963 040 021
 Ressort de protection
- 050 311 902
*- 151 775 010 Ensemble fixation
 Plaque d'interface
6 051 770 101
 Vis H 8 x 20
7 933 011 279
 Vis CHc M 8 x 10
8 933 151 147
 Vis HM 8 x 25
9 NC / NS
 Rondelle W8
14 88 664
 Rondelle MN 8
15 963 040 019
 Ecrou HM 8
16 953 010 019
*10 151 790 160 Equipement d'air 1/2"
(voir Doc. 573.403.050)
13 050 102 401 Raccord,
M 3/4 NPS - M 1/2 G
19 050 102 437 Raccord inox,
M 1/2 BSP - M 26 x 125
24 905 210 403 Coude MF 1/2 inox
25 552 473 Mamelon MM 3/8" - 1/2"
26 552 428 Coude FF 1/2"
- 905 210 503 Raccord inox
M 3/8 NPT - M 1/2 JIC
SAMES KREMLIN
Désignation
Bare pump,
model 40C50
 Air motor,
model 1000-4 (refer to
Doc. 573.045.050)
 Fluid section,
model C50 (refer to Doc.
573.032.050)
 Tie-rod, connecting
 Nut, model HM 10
 Washer, model MN 10
 Protective spring
Mounting assembly
 Plate
 Screw, model H 8 x 20  Schraube H 8 x 20
 Screw,
model CHc M 8 x 10
 Screw,
model HM 8 x 25
 Washer, model W8
 Washer, model MN 8
 Nut, model HM 8
Air supply, model 1/2"
(refer to Doc.
573.403.050)
Fitting, double male,
3/4 NPS - 1/2 G
Fitting, stainless steel,
double male,
1/2 BSP - 26 x 125
Elbow, model MF 1/2
stainless steel
Nippel, model double
male 3/8" - 1/2"
Elbow, FF 1/2"
Adaptor, stainless steel,
double male, 3/8 NPT
- # 5 JIC (1/2 JIC)
WALL MOUNTED PUMP, model 40C50
without filter, without suction rod
BOMBA MURAL, tipo 40C50
sin filtro, sin caña de aspiración
Description
Pumpe 40C50, nackt
 Luftmotor 1000-4
(siehe Dok.
573.045.050)
 Hydraulikteil C50
(siehe Dok.
573.032.050)
 Stehbolzen
 Mutter HM 10
 Scheibe MN 10
 Feder
Montageplatte kpl.
 Befestigunsplatte
 Schraube
CHc M 8 x 10
 Schraube HM 8 x 25
 Scheibe W8
 Scheibe MN 8
 Mutter HM 8
Luftausrüstung 1/2"
(siehe Dok. 573.403.050)
Doppelnippel
AG 3/4 NPS - 1/2 G
Nippel Edelstahl
AG 1/2 BSP - M 26 x 1,25
Winkelnippel Edelstahl
AG/IG 1/2
Nippel, AG/AG 3/8" - 1/2" Manguito, MM 3/8" - 1/2"
Winkelnippel IG 1/2"
Doppelnippel Edelstahl
3/8 NPT - 1/2 JIC
2
Bezeichnung
Bomba sola, tipo 40C50 1
 Motor, tipo 1000-4
(consultar Doc.
573.045.050)
 Hidráulica, tipo C50
(consultar Doc.
573.032.050)
 Tirante
 Tuerca, tipo HM 10
 Arandela, tipo MN 10
 Muelle de protección
Conjunto de fijación
 Placa
 Tornillo, tipo H 8 x 20
 Tornillo,
tipo CHc M 8 x 10
 Tornillo,
tipo HM 8 x 25
 Arandela, tipo W8
 Arandela, tipo MN 8
 Tuerca, tipo HM 8
Equipo de aire 1/2"
(consultar Doc.
573.403.050)
Racor,
M 3/4 NPS - M 1/2 G
Racor inox,
M 1/2 BSP - M 26 x 125
Codo MH 1/2 inox
Codo, HH 1/2"
Racor inox
M 3/8 NPT - M 1/2 JIC
Doc. / Dok. : 573.257.050
#
151.775.050
Denominación Qté
1
1
4
4
4
1
1
1
1
1
2
2
2
2
1
1
1
1
1
1
1