Publicité
Top Plate
Remove
Plaster Ground
Escutcheon
1. Prior to Escutcheon installation, verify that the plaster ground has been removed from the
valve so that the trim will fit properly.
2. Screw on the Mounting Sleeve passing through the Escutcheon such that the outer rim of the
sleeve presses up firmly against the Escutcheon, holding it in place against the wall.
Note:
• The orientation of the Mounting Sleeve is dependent upon whether the valve was installed
closer or further from the finished wall.
Optional
An optional decal sheet was included with the packaging.
These decals on this sheet can be used in place of the numbers
on the Escutcheon according to the valve position function.
MOEN LIFETIME LIMITED WARRANTY
Moen products have been manufactured under the highest standards of quality and workmanship. Moen warrants to
the original consumer purchaser for as long as the original consumer purchaser owns their home (the "Warranty Period"
for homeowners), that this faucet will be leak and drip-free during normal use and all parts and finishes of this faucet will
be free from defects in material and manufacturing workmanship. All other purchasers (including purchasers for industrial,
commercial and business use) are warranted for a period of 5 years from the original date of purchase (the "Warranty
Period" for non-homeowners).
If this faucet should ever develop a leak or drip during the Warranty Period, Moen will FREE OF CHARGE provide the
parts necessary to put the faucet back in good working condition and will replace FREE OF CHARGE, any part or finish that
proves defective in material and manufacturing workmanship, under normal installation, use and service. Replacement
parts may be obtained by calling 1-800-289-6636 (Canada 1-800-465-6130), or by writing to the address shown. Proof
of purchase (original sales receipt) from the original consumer purchaser must accompany all warranty claims. Defects or
damage caused by the use of other than genuine Moen parts are not covered by this warranty. This warranty is applicable
only to faucets purchased after December 1995 and shall be effective from the date of purchase as shown on purchaser's
receipt.
This warranty is extensive in that it covers replacement of all defective parts and finishes. However, damage due to
installation error, product abuse, product misuse, or use of cleaners containing abrasives, alcohol or other organic solvents,
whether performed by a contractor, service company, or yourself, are excluded from this warranty. Moen will not be
responsible for labor charges and/or damage incurred in installation, repair or replacement, nor for any indirect, incidental
or consequential damages, losses, injury or costs of any nature relating to this faucet. Except as provided by law, this
warranty is in lieu of and excludes all other warranties, conditions and guarantees, whether expressed or implied,
statutory or otherwise, including without restriction those of merchantability or of fitness for use.
Some states, provinces and nations do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also
have other rights which vary from state to state, province to province, nation to nation. Moen will advise you of the
procedure to follow in making warranty claims. Simply write to Moen Incorporated using the address below. Explain the
defect and include proof of purchase and your name, address, area code and telephone number.
3
2. Re-assemble the top plate to the transfer valve body by turning it clockwise until handtight (take caution when handling the top
plate threads) and then turn an additional 1/2 turn with a wrench.
Note:
• The proper torque of the top plate into the transfer valve body is 25 in-lbs. (2.8 N-m).
3. If the trim is to be installed at a later time, re-install the plaster ground to protect the valve.
Handle Stem Position for Handle Adapter/Handle Assembly
For correct handle position/outlet flow designation, make sure that the handle stem flats locating mark is facing upwards and away
(opposite direction) from the inlet.
Mounting Sleeve
(Reversible — see
illustration above)
Mounting Sleeve
(Reversed)
Attach The Handle
1. Place the Handle onto the valve stem as shown above. Test the
Handle rotation so that it comes to a stop at all three stop locations
on the Escutcheon. If this is not the case, remove the handle, rotate
it 180°, and replace the Handle onto the valve stem.
2. Fasten the Handle to the valve stem using the supplied torx screw.
3. Push the Plug Button into the Handle hole until it snaps into place.
CONSUMER INFORMATION
Faucets made of leaded brass alloys may contribute small amounts of lead to water that
is allowed to stand in contact with the brass. The amount of lead contributed by any
faucet is highest when the faucet is new. The following steps may reduce potential
exposure to lead from faucets and other parts of the plumbing system:
• Always run the water for a few seconds prior to use for drinking or cooking
• Use only cold water for drinking or cooking
• If you wish to flush the entire plumbing system of water that has been standing in
the pipes or other fittings, run the cold water until the temperature of the water
drops, indicating water coming from the outside main
• If you are concerned about lead in your water, have your water tested by a certified
laboratory in your area
Moen Incorporated • 25300 Al Moen Drive • North Olmsted, OH 44070-8022 U.S.A.
In Canada Moen Inc. • 2816 Bristol Circle • Oakville, Ontario L6H5S7
HELPLINE:
1 (800) BUY-MOEN
[289-6636]
In the U.S. call our toll free Helpline number, for answers to
any product installation, or warranty questions.
In Canada:
Toronto: 905-829-3400;
Rest of Canada: 1-800-465-6130
In Mexico:
(84) 88-08-26, 88-08-27,
o 91-800-84-345
INS2016
Publicité
