Continental Fireplaces Constructeur 36 Serie Manuel D'installation Et D'opération page 53

Tray Tray
Media
Media
Tray
Tray
Holes under log
Holes under log
(not illustrated). (not illustrated).
Holes under log
Holes under log
(not illustrated).
(not illustrated).
1
1
Media
Media
Tray
Tray
A1
A1
1
1
1. Place the holes in log #1 on A1 and A2.
Holes under log
Ensure the notch fits around the pilot shield. Holes under log
A1
A1
Holes under log (not illustrated). (not illustrated).
Holes under log
(not illustrated). (not illustrated).
Holes under log
Holes under log
1 1
(not illustrated).
(not illustrated).
1 1
A1 A1
2 2
C1 C1
1
1
2
2
C1
C1
Holes under log
Holes under log
Hole under log
Hole under log
(not illustrated). (not illustrated).
(not illustrated) (not illustrated)
3. Place the holes in log #3 on C1 and C2. Do not
cover any burner ports.
Hole under log
Hole under log
4 4
(not illustrated)
(not illustrated) 1 1
NOTE: Place glowing embers on the burner, in front of the large clusters of ports (not illustrated). The burner has
been designed to have large flames in these locations. If not, blue flames will be present. 2 2 2 2
C1 C1
4
4
2
2
Hole under log Hole under log
(not illustrated) (not illustrated)
4 4
2
2
5. Place the hole in log #5 on D1. Place the
opposite end on the notch in log #3.
B2
B2
B1 B1
Notch Notch
A2
A2
Notch
Notch
A2
A2
Notch
Notch
3 3
A2 A2
C2 C2
3
3
C2
C2
Notch Notch
3 3
1 1 5 5
Notch
Notch
3 3
C2 C2
D1 D1
1
5
1
5
3
3
D1
D1
Notch Notch
1 1 5
5
3 3
D1 D1
Tray Edge Tray Edge
C2 C2
C1 C1
Media
Media
Tray Edge
Tray Edge
Holes under log Holes under log
(not illustrated). (not illustrated).
Holes under log
Holes under log
Media
Media
(not illustrated).
2
2
(not illustrated).
Tray Edge
Tray Edge
B2 B2
B1 B1
2
2
2. Place the holes in log #2 on B1 and B2. Do not
cover any burner ports.
B2
B1
B2
B1
Holes under log
Holes and notch Holes under log Holes and notch
(not illustrated).
(not illustrated). not illustrated. not illustrated.
Holes and notch
Holes and notch
4
4
2 not illustrated.
2
not illustrated.
2
2
B2
B1 B2
B1
4
4
2
2
Holes and notch Holes and notch
not illustrated.
not illustrated.
4. Place the locator on log #4 into the hole in log
#2. Place the opposite end on the notch in log
#1.
4 4
4
4
1
2
2
2 2
6 6
4
4
1
2
2
6
6
4
4
1
2
2
6 6
6. Place the bottom of log #6 against the edge of
the media tray. Ensure the top branch engages
with the left end of log #3.
7. Cover the media tray with charcoal as desired
(not illustrated). Ensure charcoal is not on
burner pan.
Stud
Stud
(Log #5)
(Log #5)
finishing
D1
D1
Stud
Stud
(Log #5)
(Log #5)
1 1
1
1
1
1
1 1
3 3
1
1
3
3
Top Branch Top Branch
1
1
1
Top Branch
Top Branch
3 3
3
3
5 5
1
3
3
5
5
Top Branch
Top Branch
1
3 3
5
5
W415-3094 / B / 05.09.22
EN
53