Publicité
Les langues disponibles
Les langues disponibles
PLEASE START BY READING THESE IMPORTANT SAFETY RULES • SAVE THESE INSTRUCTIONS
This safety alert symbol means "Caution" - failure to comply with such an instruction involves risk of personal
injury or damage to property. Please read these warnings carefully.
This gate drive mechanism is designed and tested to offer appropriately safe service provided it is installed and
operated in strict accordance with the following safety rules.
Incorrect installation and/or failure to comply with the following instructions may result in serious personal injury
or property damage.
When using tools and small parts to install or
carry out repair work on a gate exercise caution
and do not wear rings, watches or loose
clothing.
Installation and wiring must be in compliance
with your local building and electrical
installation codes. Power cables must only be
connected to a properly earthed supply.
Any entrapment possibility by the moving wing
between wing & walls must be secured with
safety edges or IR-sensors.
Please remove any locks fitted to the gate in order
to prevent damage to the gate.
After the installation a final test of the full
function of the system and the full function of
the safety devices must be done.
This drive cannot be used with a gate
incorporating a wicket door unless the drive
cannot be operated with the wicket door open.
Contents: General advice on
installation and use:
Content of the carton: Page 1
figures
1
+
2
Before you begin: Page 2
Checklist: Page 2, figure
Gate types/installation height:
4
Page 2, figure
A-F
Gate configuration:
Page 2, figure
5
+
6
A-E
Gate stops:
7
Page 2, figure
CONTENT OF THE CARTON HC300MLS/400MLS
(1) Motor
(2) Electronic Control
(3) Postbracket
(4) Key
(5) Gate fixing bracket
(6) Capacitor
(7) Manual
(8) Clevis pin and rings
(9) 3-Channel remote control
(10) IR Sensor
(11) Flashing lamp
(12) Hexagonal key
709198B-GB - 05.2004
All manuals and user guides at all-guides.com
Post bracket/Gate fixing bracket:
Page 2-3, figure
Installing the drive arms:
Page 3, figure
Release of drive arms:
Page 3, figure
3
Wiring:
Page 3, figure
Maintenance work: Page 3
Electrical Installation + electronic
control: Page 3, figure
Security: Page 4
1
It is important to make sure that the gate always
runs smoothly. Gates which stick or jam must be
repaired immediately. Employ a qualified technician
to repair the gate, never attempt to repair it yourself.
Keep additional accessories away from children. Do
not allow children to play with pushbuttons or remote
controls. A gate can cause serious injuries as it
closes.
Disconnect electric power to the system before
making repairs or removing covers.
A disconnecting device must be provided in the
permanently-wired installation to guarantee all-
pole disconnection by means of a switch (at least
3mm contact gap) or by a separate fuse.
Make sure that people who install, maintain or
operate the gate drive follow these instructions.
Keep these instructions in a safe place so that you
can refer to them quickly when you need to.
The full protection against potential squeeze or
entrapment must work direct when the drive arms
are installed.
Flashing Lamp:
8
A-F
Infrared sensor:
10
Initial setting of Remote control:
11
9
-
A-B
Initial Operation: Page 6
12
A-C
Technical Data: Page 6
12
A-E
CONTENT OF THE CARTON HC300ML/400ML
(1) Motor 2x
(2) Electronic Control
(3) Postbracket 2x
(4) Keys 2x
(5) Gate fixing bracket 2x
(6) Capacitor 2x
(7) Manual
(8) Clevis pin and rings 2x
(9) 3-Channel remote control
(10) IR Sensor
(11) Flashing lamp
13
Page 5, figure
A-C
14
Page 5, figure
A-F
Page 5, figure
15
A-B
2
Publicité
