Panasonic SC-PMX802M Mode D'emploi page 12

Using the AUX IN input
You can change the input level etc. when you listen to
the audio from a portable audio player etc. connected to
AUX IN terminal.
Preparation
Connect the external equipment to AUX IN terminal.
To adjust the input level
You can adjust the input level.
1
Press [SOUND] repeatedly to select
"INPUT LEVEL".
2
Press [2, 1] to select "LOW" or "HIGH" and
then press [OK].
Note:
• The factory default is "HIGH".
• Select "LOW" if the sound is distorted during "HIGH" input
level.
• Read the operating instructions of the external music
device for details.
• Components and cables are sold separately.
AUX-IN auto play
The system will automatically switch to AUX source
when it detects the signal from an external music device.
This function also works in standby mode.
1
Press [RADIO, EXT-IN] repeatedly to select
"AUX".
2
Press [SETUP] repeatedly to select
"AUX-IN AUTO PLAY".
3
Press [2, 1] to select "ON" and then press [OK].
Note:
• The factory default is "OFF".
• This function does not work when the volume of the
external music device is low, increase its volume.
• When the function is switched off and every time you switch to
AUX source, "AUX-IN AUTO PLAY IS OFF" will be shown once.
• Stop or pause the external music device before you change
to other music source or to standby mode so as to prevent
the automatic switch to AUX source.
• When you use this function in standby mode, it may require
some seconds to be output the sound.
• If this function is set to "ON", the standby power
12
consumption will increase. (Approx. 0.15 W)
12
Using the PC input
You can play back music on the PC with this system's
speakers by connecting a PC to the PC IN terminal on
the main unit.
Before connecting to a PC
Follow the steps below.
• Refer to the following for the recommended OS
versions for your PC:
– Windows 8, Windows 8.1, Windows 10
– OS X 10.7, 10.8, 10.9, 10.10, 10.11,
macOS 10.12, 10.13, 10.14, 10.15
1 Download and install the dedicated driver to the
PC. (Only for Windows OS)
Download and install the driver from the website
below.
https://panasonic.jp/support/global/cs/audio/
(This site is in English only.)
2 Download and install the dedicated app
"Panasonic Audio Player " (free of charge) on
2
your PC. (For Windows OS and OS X)
Download and install the app from the website
below.
https://panasonic.jp/support/global/cs/audio/
(This site is in English only.)
Listening to audio from a PC
1
Disconnect the AC mains lead.
2
Connect the main unit and a PC.
Main unit (rear)
USB-DAC port
Type B
USB 2.0 cable
(not supplied)
3
Connect the AC mains lead to the main unit and
turn this system on.
4
Press [RADIO, EXT-IN] repeatedly to select "PC".
5
Operate the PC for playback.
Note:
• When you play back high-resolution audio, it is
(as of May 2021)
recommended that you use a compatible USB 2.0 High
Speed Cable.
Sound effects
Changing the sound quality
1
Press [SOUND] repeatedly to select a sound effect.
2
Press [2, 1] to select the desired setting.
BASS
TREBLE
SURROUND
[CD] (CD-DA)
CD HIGH RES
RE-MASTER
By main unit only
Turn [BASS] or [TREBLE] to adjust the level.
PC
USB
Type A
-4 to +4
"ON SURROUND" or
"OFF SURROUND"
"ON" or "OFF".