Publicité
Les langues disponibles
Les langues disponibles
Connecting to a TV with component video input connectors
If your monitor or projector has component
video input connectors (Y, C
/P
, C
/P
),
B
B
R
R
connect your PlayStation
2 console using the
®
SCPH-10100
component AV cable (for
U
PlayStation
2) (sold separately). This will
®
provide the best picture.
Before connecting
If you connect your PlayStation
2 console to a
®
television using the component AV cable
without first setting the "Component Video
Out" option under the "System Configuration"
menu to "Y Cb/Pb Cr/Pr," the TV screen
might not display properly. Before connecting
your console with the component AV cable,
first use the supplied AV cable (integrated
audio/video) and make sure that the
"Component Video Out" option is set to
"Y Cb/Pb Cr/Pr."
Note
The PlayStation
2 console is not compatible with HDTV
®
unless the proper software and connecting devices are
used.
Refer to the instruction manual for your TV for details.
When turning on the console for the first time
The initial setup screen appears.
Set "Language," "Time Zone" and "Daylight Savings Time
(Summer Time)" according to the instructions on the
screen.
Settings can be adjusted later in the System Configuration
menu. For details, see "Using the System Configuration
menu" on page 9.
To AV MULTI OUT
connector
To audio
To component
input
video input
connectors
Connecting digital audio components
This section explains how to connect the
PlayStation
2 console to audio equipment with
®
digital connectors (such as Dolby Digital
optical (AC-3) output). Using digital receivers
and amplifiers, you can enjoy features such as
multi-channel sound and surround sound.
Connecting to a receiver or
amplifier, "MD (Minidisc)" deck
or "DAT (Digital Audio Tape)"
deck with a digital connector
Use a commercially available optical digital
cable (sold separately) and set "DIGITAL OUT
(OPTICAL)" in the System Configuration menu
to "On" (the default setting).
For details on the System Configuration menu,
see page 15.
Rear panel
Receiver or amplifier,
MAIN
MD deck or DAT deck
POWER
DIGITAL INPUT
~
AC IN
DIGITAL OUT
OPTICAL
AV MULTI OUT
(OPTICAL)
Notes
• Refer also to the instructions supplied with the
component to be connected.
• You cannot directly make digital audio recordings of
discs recorded in Dolby Digital format or DTS format
using an MD or a DAT deck.
Connecting to an audio
component with a built-in DTS*
or Dolby Digital** decoder
(DVD video only)
By connecting to audio equipment with a built-
in DTS or Dolby Digital decoder (sold
separately), you can playback sound recorded
on your DVD video in Dolby Digital (AC-3) or
DTS format to reproduce the effect of listening
in a movie theater or concert hall.
Connect the component via the DIGITAL OUT
(OPTICAL) connector using an optical digital
cable (sold separately).
PlayStation
2
®
console
Optical digital cable
(sold separately)
Audio component
with a built-in DTS
or Dolby Digital
decoder
Speakers
Setups for the DVD player on your
PlayStation
2 console
®
Some setup adjustments are necessary for the
DVD player depending on the components to
be connected.
For details on using the Setup display, see page
23.
• When you connect an audio component with a
built-in DTS decoder
Set "DIGITAL OUT (OPTICAL)" to "On" and
then set "DTS" to "On" in the "Audio Setup"
display.
• When you connect an audio component with a
built-in Dolby Digital decoder
Set "DIGITAL OUT (OPTICAL)" to "On" and
then set "Dolby Digital" to "On" in the
"Audio Setup" display.
Note
Refer to the operating and setup instructions for the audio
components to be connected.
* "DTS" and "DTS Digital Out" are trademarks of Digital
Theater Systems, Inc.
** Manufactured under license from Dolby Laboratories.
"Dolby" and the double-D symbol are trademarks of
Dolby Laboratories.
Confidential unpublished works. ©1992-1997 Dolby
Laboratories. All rights reserved.
11
US
Publicité
