Adler europe AD 7723 Mode D'emploi page 7

19. Place the fan heater only on flat, stable surface
20. Always turn the fan heater off and set the thermostat dial to minimum before removin
the power plug from the socket.
21. Never use the fan heater in high humidity rooms – bathroom, shower room, swimming
pools etc. The humidity can cause short circuit, and effect in damaging the device.
22. The operating fan heater needs to be under supervision and in sight all the time. If you
are leaving the room with the fan heater, always turn the fan heater off. If the fan heater is
not used, the power plug has to be removed from the power outlet.
23. Do not connect the fan heater to the automatic switching device, for example
temperature controlling device or time switch.
24. Flammable materials, for example furniture, bedclothes, paper, clothes, curtains should
be kept at least one meter from the fan heater.
25. Do not cover the device or put any objects on it while it is operating. Do not use the
device to dry clothes.
26. The power cord should not be placed above the fan heater, and it should not touch or
be placed near hot surfaces of the fan heater. Do not place the fan heater directly under
the power outlet.
27. The heating surfaces can heat to a temperature of 60 °C or higher. The fan heater
should be in a place that children and animals do not have access to.
28. The device is not intended to be installed or used in vehicles.
29. Some parts inside the device can be hot or cause sparking. Do not use the fan heater in
places, where gasoline, paints or other flammable materials are used or stored.
30. Do not use this heater in the immediate vicinity of a bathtub, shower or swimming pool
31. Do not use this heater if it has been dropped
32. Do not use if there are visible signs of damage to the heater
33. Use the heater on a level and stable surface or attach it to the wall, if provided for by the
manufacturer
WARNING: Do not use this heater in small rooms where there are people who are unable to
leave them by themselves, unless constant supervision is ensured.
WARNING: To reduce the risk of fire, keep textiles, curtains or other flammable materials at
least 1 m away from the heater air outlet.
PRODUCT DESCRIPTION: CERAMIC FAN HEATER WITH REMOTE CONTROL (picture 1 & 2)
1. Control Panel 2. Digital Display
5. Power Switch 6. Air inlet grid with dust mesh filter
8. Remote Control:
A. Power button B. Low / High heat power button
D. Timer button E., F. Room temperature adjustment + / - buttons
USE
ROOM TEMPERATURE ADJUST: Pressing buttons (E or F) will increase or decrease the desired room temperature. After setting desired
temperature the heater in device will switch on or switch off to maintain the desired room temperature. Device enables for temperature
setting from 10-35 degree Celsius. When the room temperature lower by 4℃ than the settled temperature of unit, device starts to heat on
high power automatically. Then when the room temperature lower by 2℃, the device start to heat on lower power automatically. If room
temperature reach the setting temperature level, the heating is stopped, the fan is permanently work on till room temperature lower than
the setting temperature by 2℃, the unit automatically return to lower power heating.
TIMER: Pressing button (D) will set the timer from 1 hour increments up to 8 hours. After the set time the device will power off.
OSCILLATION: Pressing button (C) will set the device to turn on the base (4) from left to right, totally 45 degree.
LOW HEAT/HIGH HEAT: Pressing button (B) will switch between power levels:
• Low Heat = 1000W
• High Heat = 2000W
POWER SWITCH (5): Pressing it to switch on the device and press it again to switch off the device from supply.
POWER BUTTON (A): Pressing it will power on or off the device from Standby mode.
Remote control (8) operation is same as manual operation of buttons on control panel.
To use the device with the remote control (8) supplied, remove the small battery compartment located at the base of the remote control. To
remove the battery compartment, simply squeeze the small tab and pull. Insert 1 x CR2025 (3V) lithium battery into the small crevice as
illustrated (picture 3).
IMPORTANT: The + symbol on the battery inserted should be facing upwards. Firmly close the battery compartment to begin using the
Remote Control (8).
3. Heat Outlet
7. Tip over Switch (Located on the Base)
C. Oscillation button
7
4. Base