Nilfisk Advance CA240 Mode D'emploi page 20

•
Remove the brushes by pushing out the brush shafts.
Wash the brushes thoroughly in clean water.
•
Lay the machine on its side and wipe clean the
rubberised drum and machine body with a damp
cloth.
•
Right the machine and refit brushes.
7 Storage
After use always clean the machine as described. Check
that machine is in Transport mode, i.e. brushes above
the floor. Never store the machine with brushes in
contact with the floor, as this causes distortion of the
bristles.
The machine should be stored with the handle in the
upright position, with the supply cord wrapped around
the cable hooks on the handle, ensuring that the plug
is not trailing on the floor. Store the machine in a dry
indoor area only.
8 Maintenance
WARNING - Before undertaking maintenance
operations or adjustments switch off machine and
unplug from the electricity supply.
The machine requires minimum maintenance apart from
the following checks by the operator.
•
Supply cord - Regularly inspect sheath, plug and
cord anchorage for damage or loose connection.
•
Brushes - For maximum life wash the brushes
regularly. Ensure machine is in Transport mode
when not in use. Store additional brushes in a
vertical position to avoid bending bristles. Check
for permanent bending of bristles in a particular
direction. This may occur if the machine is operated
for several days without removing the brushes,
which is not recommended. If this occurs, reverse
the brush so that the bent bristles are automatically
straightened.
•
Rubberised drum - This may wear out after years of
use. If this occurs the water collection performance
will decrease. It should be replaced by an authorised
Service Agent.
•
Solution tank filter - The filter prevents clogging of
the drip holes in the tank. Periodically clean the filter
to ensure uniform discharge of liquid. In case of non
uniform discharge from the drip holes, back flush the
tank in running water. Clean the drip holes using wire
or a blunt pin.
9 After sales service
Should you require after sales service please contact the
supplier from whom you purchased the machine, who
will arrange service. Repairs and servicing should only
be performed by trained staff. Improper repairs can
cause considerable dangers to the user.
20
All manuals and user guides at all-guides.com
10 Technical specification
230-240V Ê 50 Hz. / 110-120V Ê 60 Hz. Class I
construction. Enclosure to IPX4.
Fitted with a 12m supply cord and plug.
Cleaning capacity ( Theoritcal )
Cleaning width
Motor power
Average running current at 230V
50 Hz
Average running current at 110V
60 Hz
Brush speed at 230V 50 Hz
Brush speed at 110V 60 Hz
Solution tank capacity
Noise level
Handle vibration (see note 2)
Body height
Handle height
Width
Length
Weight
1 - Noise levels measured at a distance of 1 metre from
2 - Handle vibration does not exceed 2,5 m/s², when
11 Accessories
Standard brush (1)
Soft brush (1)
Hard brush (1)
Side brush
Escalator brush (1)
Standard brush (1)
Soft brush (1)
Side brush
Tank conversion kit
Trolley (all models)
IMPORTANT : Genuine accessories are only available
from authorised Service Agents.
12 Brush selection guide
Type of floor
Granite, Ceramic, Vinyl
Mosaic
Marble
Smooth concrete
Wood, Rubber
Shortpile carpet
Others
Model
(see note 1)
machine and 1,6 metres above floor, when washing
a hard floor. Measurements recorded using a hand
held meter.
operating on a smooth hard surface.
Item
First time
cleaning
Standard
Hard / Standard
Standard
Hard
Standard / Soft
Soft
To suit individual floor conditions
CA240 CA330
m²/h 250 350
cm 24 34
W 550 750
A 2,5 2,7
A 7,0 7,5
rpm 650 650
rpm 780 780
ltr 1,2 1,7
dB(A) 68 69
m/s² < 2,5 < 2,5
cm 21 21
cm 111 111
cm 34,0 44,0
cm 37,8 37,8
kg 20 23,5
Part No.
CA330 55900130
CA330 55900131
CA330 55900089
CA330 55900132
CA330 55900090
CA240 55900127
CA240 55900133
CA240 55900134
CA330 55900307
55903395
Maintenance
cleaning
Standard / Soft
Standard / Soft
Soft
Standard
Standard / Soft
Soft