Publicité
Les langues disponibles
Les langues disponibles
To change the AM/FM channel intervals
– AREA
When this unit is shipped from the factory, the
channel intervals are set to 10 kHz for AM and 200
kHz for FM (AREA US settings).
You will have to change the channel intervals
when using this unit in an area other than North
America and South America.
• AREA EU:
Select this when using this unit in
an area other than North and
South America. (9 kHz for AM and
50 kHz (for manual tuning) / 100
kHz (for searching) for FM)
• AREA US:
Select this when using this unit in
North or South America. (10 kHz
for AM and 200 kHz for FM)
Note:
If the channel intervals settings are changed, the names
assigned to the stations will be erased from memory. To
reassign the names, see "Assigning names to the
sources" on pages 21.
To adjust the line input level
(For KD-SH77 only)
Adjust the line input level properly when an
external component is connected to the LINE IN
plugs.
When shipped from the factory, the line input level
is set at level 00.
If the input level of the connected component is
not high enough, increase the input level properly.
Without adjusting the line input level, you may be
surprised at a loud sound when you change the
source from the external component to another
source.
To select the external component to use
– EXT INPUT (For KD-SH55 only)
You can connect the external component to the
CD changer jack on the rear using the Line Input
Adaptor KS-U57 (not supplied).
To use the external component as the playback
source through this unit, you need to select which
component – CD changer or external component
– to use.
When shipped from the factory, CD changer is
selected as the external component.
• LINE INPUT:
To use the external component
other than CD changer.
• CD CHANGER: To use the CD changer.
Note:
For connecting the Line Input Adaptor KS-U57 and the
external component, refer to the Installation/
Connection Manual (separate volume).
20
EN17-23.KD-SH77_55[J]f
To adjust the auxiliary input level
– AUX ADJ
Adjust the auxiliary input level properly when an
external component is connected to the MP3
INPUT jack.
When shipped from the factory, the auxiliary input
level is set at level 00.
If the input level of the connected component is not
high enough, increase the input level properly. Without
adjusting the line input level, you may be surprised at
a loud sound when you change the source from the
external component to another source.
To select the target component to operate
through this receiver
– KEY SELECT (For KD-SH77 only)
You can operate either JVC's VCR or DVD player
through this receiver, by using the number buttons
on the control panel.
When shipped from the factory, these number
buttons are set to be used for the DVD operations.
To use these number buttons on the control panel
– LINE ADJ
for DVD or VCR operations, see page 25.
To change the FM tuner selectivity
– IF FILTER
In some areas, adjacent stations may interfere
with each other. If this interference occurs, noise
may be heard. This unit has been preset to
automatically reduce this interference noise
("AUTO") when shipped from the factory.
• AUTO:
• WIDE:
To turn the demo mode on or off
– DEMO MODE
You can turn the demo mode on or off. When
shipped from the factory, "DEMO ON" is selected.
• DEMO ON:
• DEMO OFF: Turns the demo mode off.
Note:
If the unit has been reset (and the power is on),
demonstration will start if no sound comes in for about
10 seconds.
20
When this type of interference occurs,
this unit automatically increases the
tuner selectivity so that interference
noise will be reduced. (But the stereo
effect will also be lost.)
Subject to the interference from
adjacent stations, but sound quality
will not be degraded and the stereo
effect will not be lost.
Turns the demo mode on. The
demonstration will start automatically
if no sound comes in for 3 minutes.
01.1.9, 4:32 PM
Publicité
