Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
PARTS LIST:
Qty
Description
1
Driver/Left Frame Mounting Bracket
1
Passenger/Right Frame Mounting Bracket
Driver/Left
1
Bull Bar Mounting Bracket
Passenger/Right
1
1
LED Light Bar
4
Large Spacer Washers
2
10-1.50mm x 120mm x 30mm Hex Bolts
4
10-1.50mm x 30mm Hex Bolts
2
10mm x 30mm OD x 2.5mm Large Flat
Washers
Passenger/Right
Side Frame Bracket
Passenger/Right Side Bull
Bar Mounting Bracket
EQUIPMENT NEEDED:
Safety Glasses
Ratchet Set
Pliers or Adjustable Wrench
IMPORTANT NOTES:
Bull Bar may interfere with parking sensors on the bumper.
The LED light bar can be wired into the factory lighting, or a wiring harness can be purchased separately.
If state law requires a front license plate, a relocation kit is available separately.
For cleaning, mild soap may be used to clean the Bull Bar, and aluminum polish may be used on the
stainless steel to polish small scratches and scuffs on the finish.
REMOVE CONTENTS FROM BOX, VERIFY ALL PARTS ARE PRESENT, & READ INSTRUCTIONS
CAREFULLY. NOTE: PROFESSIONAL INSTALLATION IS RECOMMENDED.
Bull Bar Mounting Bracket
(4) Spacer Washers
Page 1 of 15
Qty
Description
10
10mm x 20mm OD x 2mm Small Flat Washers
6
10mm Lock Washers
6
10mm Hex Nuts
4
8-1.25mm x 35mm Hex Bolts
4
8mm x 24mm OD x 2mm Flat Washers
4
8mm Lock Washers
1
Wrench
Driver/Left Side Bull
Bar Mounting Bracket
I-Sheet Number 10782 Rev.B
3-1/2" OVAL BULL BAR
05-15 TOYOTA TACOMA
Driver/Left Side
Frame Bracket
03/08/16
Publicité
Manuels Connexes pour LUND 47121210
Sommaire des Matières pour LUND 47121210
- Page 1 I-Sheet Number 10782 Rev.B 3-1/2” OVAL BULL BAR 05-15 TOYOTA TACOMA PARTS LIST: Description Description Driver/Left Frame Mounting Bracket 10mm x 20mm OD x 2mm Small Flat Washers Passenger/Right Frame Mounting Bracket 10mm Lock Washers Driver/Left 10mm Hex Nuts Bull Bar Mounting Bracket Passenger/Right Bull Bar Mounting Bracket 8-1.25mm x 35mm Hex Bolts...
- Page 2 I-Sheet Number 10782 Rev.B 3-1/2” OVAL BULL BAR 05-15 TOYOTA TACOMA LIGHT BAR INSTALLATION: 1. Remove light bar from box and screw bolts and washers into each end. 2. Slide bolts into crossbeam brackets with the washers on the outside of the bracket, and tighten using the supplied allen key BULL BAR INSTALLATION: 1.
- Page 3 I-Sheet Number 10782 Rev.B 3-1/2” OVAL BULL BAR 05-15 TOYOTA TACOMA 3. Slide (1) Large Spacer Washer between the Mounting Bracket and the frame cross member, (Figures 3A & 3B). Insert (1) 10mm x 120mm Hex Bolt with (1) 10mm x 20mm OD Small Flat Washer and (1) Large Spacer Washer into and through the hole in the back of the cross member.
- Page 4 I-Sheet Number 10782 Rev.B 3-1/2” OVAL BULL BAR 05-15 TOYOTA TACOMA 4. Repeat Steps 2—4 for driver side Bracket installation. 5. Next, carefully unwrap the Bull Bar, (Figure 7). Select the passenger side Bull Bar Mounting Bracket, (Figure 8). Attach the Bracket to the end of the Bull Bar with (2) 8mm x 35mm Hex Bolts, (2) 8mm Lock washers and (2) 8mm Flat Washers, (Figure 9).
- Page 5 I-Sheet Number 10782 Rev.B 3-1/2” OVAL BULL BAR 05-15 TOYOTA TACOMA 6. With assistance, line up the mounting tabs on the Bull Bar with the outside of the (2) previously installed Frame Mounting Brackets. Bolt the Bull Bar to the Frame Mounting Brackets with the included (4) 10mm x 30mm Hex Bolts, (8) 10mm x 20mm OD Small Flat Washers, (4) 10mm Lock Washers and (4) 10mm Hex Nuts, (Figures 10A &...
- Page 6 I-Sheet Number 10782 Rev.B 3-1/2” OVAL BULL BAR 05-15 TOYOTA TACOMA LISTE DES PIÈCES : Qté Description Qté Description Support de fixation de châssis côté Petites rondelles plates de gauche/conducteur 10 mm x 20 mm de diam. ext. x 2 mm Support de fixation de châssis côté...
- Page 7 I-Sheet Number 10782 Rev.B 3-1/2” OVAL BULL BAR 05-15 TOYOTA TACOMA Pour le nettoyage, il est possible d’utiliser du savon doux pour nettoyer le pare-buffle et un produit d’entretien pour l’aluminium pour nettoyer l’acier inoxydable, afin d’effacer les petites rayures et les éraflures de surface.
- Page 8 I-Sheet Number 10782 Rev.B 3-1/2” OVAL BULL BAR 05-15 TOYOTA TACOMA 3. Enfiler (1) grande rondelle d’espacement entre le support de fixation et la barre transversale du châssis (Figures 3A et 3B). Insérer (1) boulon à tête hexagonale de 10 mm x 120 mm avec (1) petite rondelle plate de 10 mm x 20 mm diam.
- Page 9 I-Sheet Number 10782 Rev.B 3-1/2” OVAL BULL BAR 05-15 TOYOTA TACOMA 4. Répéter les étapes 2 à 4 pour l’installation du support côté conducteur. 5. Déballer ensuite le pare-buffle avec soin (Figure 7). Sélectionner le support de fixation du pare-buffle côté...
- Page 10 I-Sheet Number 10782 Rev.B 3-1/2” OVAL BULL BAR 05-15 TOYOTA TACOMA 6. Avec l’aide d’une autre personne, aligner les pattes de fixation du pare-buffle avec le côté extérieur des (2) supports de fixation de châssis installés précédemment. Boulonner le pare-buffle sur les supports de fixation de châssis en utilisant les (4) boulons à...
- Page 11 I-Sheet Number 10782 Rev.B 3-1/2” OVAL BULL BAR 05-15 TOYOTA TACOMA LISTA DE PIEZAS: Cant. Descripción Cant. Descripción Soporte de montaje del bastidor Arandelas planas pequeñas de 10 mm x izquierdo/del lado del conductor 20 mm de diámetro exterior x 2 mm Soporte de montaje del bastidor Arandelas de presión de 10 mm derecho/del lado del pasajero...
- Page 12 I-Sheet Number 10782 Rev.B 3-1/2” OVAL BULL BAR 05-15 TOYOTA TACOMA INSTALACIÓN DE LA BARRA DE LUCES: 1. Retire la barra de luces de la caja y atornille los pernos y las arandelas en cada extremo. 2. Deslice los pernos hacia los soportes de travesaño desplazable con las arandelas en la parte externa del soporte y ajuste con la llave allen que se suministra.
- Page 13 I-Sheet Number 10782 Rev.B 3-1/2” OVAL BULL BAR 05-15 TOYOTA TACOMA 3. Deslice (1) la arandela espaciadora grande entre el soporte de montaje y el travesero del bastidor (Figuras 3A y 3B). Inserte (1) perno hexagonal de 10 mm x 120 mm con (1) arandela plana pequeña de 10 mm x 20 mm de diámetro exterior y (1) arandela espaciadora grande a través del orificio en la parte trasera del travesero.
- Page 14 I-Sheet Number 10782 Rev.B 3-1/2” OVAL BULL BAR 05-15 TOYOTA TACOMA 4. Repita los Pasos 2 a 4 para la instalación del soporte del lado del conductor. 5. Luego, desenvuelva cuidadosamente la parrilla delantera (Figura 7). Seleccione el soporte de montaje de la parrilla delantera del lado del pasajero (Figura 8).
- Page 15 I-Sheet Number 10782 Rev.B 3-1/2” OVAL BULL BAR 05-15 TOYOTA TACOMA 6. Con ayuda, alinee las lengüetas de montaje en la parrilla delantera con la parte externa de los (2) soportes de montaje de bastidor previamente instalados. Atornille la parrilla delantera a los soportes de montaje del bastidor utilizando los siguientes elementos incluidos: 4 pernos hexagonales de 10 mm x 30 mm, 8 arandelas planas pequeñas de 10 mm x 20 mm de diámetro exterior, 4 arandelas de presión de 10 mm y 4 tuercas hexagonales de 10 mm (Figuras 10A y 10B).