1. Manuels
  2. Marques
  3. LUND Manuels
  4. Accessoires de voiture
  5. 10777
  6. Instructions d'installation

LUND 10777 Instructions D'installation

Masquer les pouces
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

Télécharger ce manuel
PARTS LIST:
1
Bull Bar
2
Tube Brackets (Bull Bar) passenger or driver side
2
Upper Frame Brackets (models w/o tow hooks only)
1
Driver/Left Mounting Bracket
1
Passenger/Right Mounting Bracket
1
Driver/Left Support Bracket
1
Passenger/Right Support Bracket
1
LED Light Bar
12-1.5mm x 30mm Special Fine Thread Hex Bolt
2
(for models w/o tow hooks only)
4
12-1.75mm x 35mm Hex Bolts
14
12mm x 32mm OD x 3mm Flat Washers
10
12mm Lock Washers
8
12-1.75mm Hex Nuts
Upper Frame
Bracket (no
tow hook only)
Passenger/Right
Mounting Bracket
EQUIPMENT NEEDED:
Safety Glasses
•
Ratchet Set
•
Pliers or Adjustable Wrench
•
IMPORTANT NOTES:
Bull Bar may interfere with parking sensors on the bumper.
•
The LED light bar can be wired into the factory lighting, or a wiring harness can be purchased separately.
•
If state law requires a front license plate, a relocation kit is available separately.
•
For cleaning, mild soap may be used to clean the Bull Bar, and aluminum polish may be used on the
•
stainless steel to polish small scratches and scuffs on the finish.
REMOVE CONTENTS FROM BOX, VERIFY ALL PARTS ARE PRESENT, & READ INSTRUCTIONS
•
CAREFULLY
Passenger Side
Support Bracket
(see note below)
Driver Side Support Bracket pictured
in "no-tow hook" direction. Reverse
direction for tow hook equipped
vehicles
Tube Brackets
Page 1 of 24
2
10-1.5mm x 35mm Hex Bolts
2
10mm Lock Washers
4
10mm x 27mm OD x 3mm Flat Washers
2
10-1.5mm Hex Nuts
4
8-1.25mm x 35mm Hex Bolts
4
8mm Lock Washers
4
8mm x 22mm OD x 2mm Flat Washers
2
5-.8mm x 15mm Button Head Allen Bolt
4
5mm x 10mm OD x 1mm Flat Washers
2
5mm Nylon Lock Nuts
1
Wrench (Allen bolt)
I-Sheet Number 10777
3-1/2" OVAL BULL BAR
09-15 DODGE RAM 1500
Upper Frame
Bracket (no
tow hook only)
Driver/Left
Mounting Bracket
12/19/14

Publicité

Table des Matières
loading

Manuels Connexes pour LUND 10777

Sommaire des Matières pour LUND 10777

  • Page 1 I-Sheet Number 10777 3-1/2” OVAL BULL BAR 09-15 DODGE RAM 1500 PARTS LIST: Bull Bar 10-1.5mm x 35mm Hex Bolts Tube Brackets (Bull Bar) passenger or driver side 10mm Lock Washers Upper Frame Brackets (models w/o tow hooks only) 10mm x 27mm OD x 3mm Flat Washers Driver/Left Mounting Bracket 10-1.5mm Hex Nuts...
  • Page 2 I-Sheet Number 10777 3-1/2” OVAL BULL BAR 09-15 DODGE RAM 1500 LIGHT BAR INSTALLATION: 1. Remove light bar from box and screw bolts and washers into each end. 2. Slide bolts into crossbeam brackets with the washers on the outside of the bracket, and tighten using the supplied allen key.
  • Page 3 I-Sheet Number 10777 3-1/2” OVAL BULL BAR 09-15 DODGE RAM 1500 2. Next, determine if the truck is equipped with tow hooks. For models without tow hooks: a. Remove the hex nuts from the two lower bumper bolts, (Figure 2).
  • Page 4 I-Sheet Number 10777 3-1/2” OVAL BULL BAR 09-15 DODGE RAM 1500 c. Insert the Mounting Bracket assembly up from behind the bumper. Line up the holes in the Mounting Bracket with the (2) bumper bolts. Attach the Bracket assembly to the bumper bolts with the (2) factory hex nuts.
  • Page 5 I-Sheet Number 10777 3-1/2” OVAL BULL BAR 09-15 DODGE RAM 1500 For models with tow hooks: a. Remove the (2) hex nuts holding the front of the tow hook to the bottom of the bumper bracket, (Figure 6). Leave the rear hex bolt tight for the moment.
  • Page 6 I-Sheet Number 10777 3-1/2” OVAL BULL BAR 09-15 DODGE RAM 1500 4. Next, select (1) Tube Mounting Bracket, (Figure 8). Bolt the Bracket to the end of the Bull Bar with (2) 8mm x 35mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat Washers, (Figure 9). Leave hardware loose at this time.
  • Page 7 I-Sheet Number 10777 3-1/2” OVAL BULL BAR 09-15 DODGE RAM 1500 6. Stand back from the vehicle and check to see that the Bull Bar is centered and level on the vehicle and adjust as necessary. Tighten only the hardware securing the Mounting Brackets to the vehicle first. Next tighten only the (4) 8mm Hex Bolts securing the Tube Brackets to the Bull Bar as described in Step 4.
  • Page 8 I-Sheet Number 10777 3-1/2” OVAL BULL BAR 09-15 DODGE RAM 1500 8. Reinstall the splash guard using the factory hardware. Use the included (2) 5mm x 15mm Allen Bolts, (4) 5mm Flat Washers and (2) 5mm Lock Nuts at the ends of the splash guard if required, (Figure 14).

  • Page 9: Liste Des Pièces

    I-Sheet Number 10777 3-1/2” OVAL BULL BAR 09-15 DODGE RAM 1500 LISTE DES PIÈCES : Boulons à tête hexagonale Pare-buffle M10 x 1,5 mm de 35 mm Supports de tube (pare-buffle) côté passager ou Rondelles de blocage de 10 mm conducteur Supports supérieurs de châssis (uniquement pour...

  • Page 10: Installation De La Barre Lumineuse

    I-Sheet Number 10777 3-1/2” OVAL BULL BAR 09-15 DODGE RAM 1500 Si la règlementation en vigueur impose une plaque d’immatriculation avant, un kit de déplacement est • disponible séparément. Pour le nettoyage, il est possible d’utiliser du savon doux pour nettoyer le pare-buffle et un produit •...
  • Page 11 I-Sheet Number 10777 3-1/2” OVAL BULL BAR 09-15 DODGE RAM 1500 a. Enlever les écrous à tête hexagonale des deux boulons inférieurs du pare-chocs (Figure 2). Enlever les (2) écrous d’origine à tête hexagonale des boulons inférieurs du pare-chocs Avant...
  • Page 12 I-Sheet Number 10777 3-1/2” OVAL BULL BAR 09-15 DODGE RAM 1500 Avant IMPORTANT : Sur les modèles sans crochets de remorquage, utiliser uniquement le boulon à tête hexagonale à filetage fin M12 x 1,5 mm de 30 mm fourni Rondelle plate de 12 mm...
  • Page 13 I-Sheet Number 10777 3-1/2” OVAL BULL BAR 09-15 DODGE RAM 1500 a. Enlever les (2) écrous à tête hexagonale maintenant l’avant du crochet de remorquage contre la partie inférieure du support de pare-chocs (Figure 6). Ne pas desserrer le boulon à tête hexagonale arrière pour l’instant.
  • Page 14 I-Sheet Number 10777 3-1/2” OVAL BULL BAR 09-15 DODGE RAM 1500 4. Sélectionner ensuite (1) support de fixation de tube (Figure 8). Boulonner le support sur l’extrémité du pare-buffle en utilisant (2) boulons à tête hexagonale de 8 mm x 35 mm, (2) rondelles de blocage de 8 mm et (2) rondelles plates de 8 mm (Figure 9).
  • Page 15 I-Sheet Number 10777 3-1/2” OVAL BULL BAR 09-15 DODGE RAM 1500 qui maintiennent les supports de fixation sur le véhicule. Serrer ensuite uniquement les (4) boulons à tête hexagonale de 8 mm qui maintiennent les supports de tube sur le pare-buffle en suivant les instructions de l’étape 4.

  • Page 16: Lista De Piezas

    I-Sheet Number 10777 3-1/2” OVAL BULL BAR 09-15 DODGE RAM 1500 8. Remonter le pare-boue en utilisant les éléments de fixation d’origine. Utiliser les (2) boulons Allen de 5 mm x 15 mm, les (4) rondelles plates de 5 mm et les (2) écrous de blocage de 5 mm fournis aux extrémités du pare-boue si nécessaire (Figure 14).

  • Page 17: Equipo Necesario

    I-Sheet Number 10777 3-1/2” OVAL BULL BAR 09-15 DODGE RAM 1500 Tornillos hexagonales de 10-1,5 mm x Parrilla delantera 35 mm Soportes de tubo (parrilla delantera) del lado del Arandelas de presión de 10 mm pasajero o del conductor Soportes de bastidor superior (solo modelos sin...
  • Page 18 I-Sheet Number 10777 3-1/2” OVAL BULL BAR 09-15 DODGE RAM 1500 La barra de luz LED puede conectarse con la luz de fábrica o un arnés de cableado puede comprarse por • separado. Si la ley estatal requiere una placa de licencia frontal, puede obtener un kit de reubicación por separado.

  • Page 19: Parte Delantera

    I-Sheet Number 10777 3-1/2” OVAL BULL BAR 09-15 DODGE RAM 1500 2. A continuación, determine si el camión está equipado con ganchos de remolque. Para modelos sin ganchos de remolque: a. Retire las tuercas hexagonales de los dos tornillos inferiores del parachoques (Figura 2).

  • Page 20: Table Des Matières

    I-Sheet Number 10777 3-1/2” OVAL BULL BAR 09-15 DODGE RAM 1500 c. Inserte el ensamblaje del soporte de montaje hacia arriba desde atrás del parachoques. Alinee los orificios del soporte de montaje con los (2) tornillos del parachoques. Acople el ensamblaje del soporte a los tornillos del parachoques con las (2) tuercas hexagonales.

  • Page 21: Tornillo Hexagonal De 10 Mm

    I-Sheet Number 10777 3-1/2” OVAL BULL BAR 09-15 DODGE RAM 1500 12 mm (Figura 5). IMPORTANTE: El orificio de la parte inferior del bastidor es de rosca fina. Solo use la tuerca hexagonal de rosca fina de 12-1.5 mm x 30 mm proporcionada en el kit de componentes.

  • Page 22: Arandelas De Presión De 12 Mm

    I-Sheet Number 10777 3-1/2” OVAL BULL BAR 09-15 DODGE RAM 1500 3. Repita el paso 2 apropiado para la instalación del soporte de montaje del lado del pasajero. 4. A continuación, seleccione (1) soporte de montaje de tubo (Figura 8). Atornille el soporte al extremo de la parrilla delantera con (2) tuercas hexagonales de 8 mm x 35 mm, (2) arandelas de presión de 8 mm y (2)

  • Page 23: Parte Delantera

    I-Sheet Number 10777 3-1/2” OVAL BULL BAR 09-15 DODGE RAM 1500 6. Manténgase alejado del vehículo y verifique que la parrilla delantera esté centrada y nivelada en el vehículo y ajuste según sea necesario. Ajuste solo los componentes que aseguran los soportes de montaje al vehículo primero.
  • Page 24 I-Sheet Number 10777 3-1/2” OVAL BULL BAR 09-15 DODGE RAM 1500 8. Reinstale la protección contra salpicaduras usando los componentes de fábrica. Use los (2) tornillos Allen de 5 mm x 15 mm incluidos, (4) arandelas planas de 5 mm y (2) tuercas de presión de 5 mm en los extremos de la protección contra salpicaduras si es necesario (Figure 14).

Table des Matières