BorMann Pro BPW5300 Mode D'emploi page 10

EN
Inspection and service before each operation
Cleaning of air cleaner
Element holder
When the element is very dirty or when the oil has been used up making the element dry, after cleaning the element soak it
Element
in kerosene and strongly wring out the element with one hand.
Use of heat or flame is absolutely prohibited.
Cleaning and service at respective sections
Clean at around the muffler.
Clean the cooling fins and the cooling air inlet.
Inspect and re-tighten bolts and nuts.
Inspect the fuel leakage.
Inspection and service at every 50-hour
Spark Plug Service
Recommended spark plug: E6TC
1. Disconnect the spark plug cap, and remove any dirt from around the spark plug area.
2. Remove the spark plug with a spark plug wrench.
Sealing washer
3. Inspect the spark plug. Replace it if the electrodes are worn, or if the insulator is cracked or chipped.
4. Measure the spark plug electrode gap with a suitable gauge. The gap should be 0.028~0.031 in (0.70~0.80mm). Correct
the gap if necessary, by carefully bending the side electrode.
5. Install the spark plug carefully, by hand, to avoid cross-threading.
6. After the spark plug seats, tighten with a spark plug wrench to compress the sealing washer.
If reinstalling the used spark plug, tighten 1/8-1/4 turn after the spark plug seats.
If installing a new spark plug, tighten 1 / 2 turn after the spark plug seats.
NOTICE
A loose spark plug can overhand and damage the engine.
Over tightening the spark plug can damage the threads in the cylinder head.
7. Attach the spark plug cap.
Cautions during inspection
Disconnect the ignition plug wires before inspection or adjustment to prevent unexpected start of engine.
Do not touch the engine immediately after operation to prevent burn.
Use of fire is strictly prohibited when handling the fuel (gasoline).
Make sure to clean spilled fuel sufficiently before using the engine.
Do not wash the engine with water.
Do not change the setting revolution speed carelessly. (Consult your dealer when changing the revolution speed.)
Long-time storing
When releasing the engine from operation for more than 30 days, it must be serviced and stored as follows with care to prevent the starting trouble or mal-
function due to degeneration of fuel.
1. Drain the fuel from the fuel tank and start to run the engine till it is stopped due to use-up of fuel.
2. Wash the inside of fuel tank and fuel filter with white kerosene.
Use of fire is strictly prohibited
3. Removing the ignition plug, inject a small quantity of new engine oil through the plughole.
After idling slowly for few revolutions operating the recoil starter, install the ignition plug.
Pull the recoil starter again and stop it at the position where it is felt heavy.
4. Clean the external surfaces with soft cloth and store it at a dry place free from fires.
● If the unit is left over without draining fuel, impurities in the fuel could clog the fuel passages such as the carburettor, fuel filter, or others, and cause engine
troubles.
Make sure to drain the fuel when storing the unit for a long period of time.
Sufficient care must be taken not to use fires at the vicinity when handling the fuel.
Warning!
Impurities in water may damage the high pressure pump and accessories. Make sure that the water supply to which the pressure washer is connected has
the appropriate specifications for an efficient and safe operation. For means of protection it is recommended to connect a water filter.
* The manufacturer reserves the right to make minor changes to product design and technical specifications without prior notice unless these changes significantly affect the performance and safety of the
products. The parts described / illustrated in the pages of the manual that you hold in your hands may also concern other models of the manufacturer's product line with similar features and may not be
included in the product you just acquired.
* To ensure the safety and reliability of the product and the warranty validity, all repair, inspection, repair or replacement work, including maintenance and special adjustments, must only be carried out by
technicians of the authorized service department of the manufacturer.
* Always use the product with the supplied equipment. Operation of the product with non-provided equipment may cause malfunctions or even serious injury or death. The manufacturer and the importer
shall not be liable for injuries and damages resulting from the use of non-conforming equipment.
10
WWW.NIKOLAOUTOOLS.GR