Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Long press BAND-+10KHz key (21) again to
disappears from the LCD.
22) 6 PIN MICROPHONE PLUG
The plug is located on the front panel of the transceiver and makes the set-
ting of the equipment into the dashboard easier.
See Cabling Diagram page 53.
23) PTT
Transmission key, press to transmit a message, "TX" is displayed and release
to listen to an incoming communication.
A) DC-POWER TERMINAL (13,2 V)
B) ANTENNA CONNECTOR (SO-239)
C) EXTERNAL SPEAKER JACK (8 Ω, Ø 3,5 mm)
D) JACK FOR OPTIONAL PA (Public Address) (Ø 3.5 mm)
E) JACK FOR OPTIONAL VOX MIKE (Ø 2.5 mm)
F) JACK FOR CW DEVICE (Ø 3.5 mm)
G) USB DATA (PC setting in option)
C) MENU FUNCTIONS
Press the MENU key (4) for 2 seconds to
"FUNC" appears on the LCD.
select
Use s/t keys (10) to
the desired function.
Use rotary PUSH knob (6) to
set
Press any key except PUSH knob (6) or wait for 5 seconds to
"FUNC" disappears from the LCD.
1) ROGER BEEP FREQUENCY
Set
the FREQUENCY of the ROGER BEEP.
At [
] menu, rotate PUSH knob (6) to
Frequency range:
Hz ~ 3
Hz, stepping frequency:
300
000
Press PUSH knob (6) to
change
2) ROGER BEEP TIME
Set
the TIME (ms) of the ROGER BEEP.
At [
] menu, rotate PUSH knob (6) to
Time range
~ 1
ms, time stepping:
50
000
(6) to
change
the step.
disable
frequency +10KHZ. "10K"
enter
in the menu function setting.
the function.
store
set
the Frequency.
Hz, default:1
10
the step.
set
the delay Time.
ms. Press PUSH knob
ms, default:
50
500
3) CW FREQUENCY
Set
the FREQUENCY of the CW.
At [
] menu, rotate PUSH knob (6) to
Frequency range:
Press PUSH knob (6) to change the step.
4) CALL FREQUENCY
Set
the FREQUENCY of the CALL tone.
At [
] menu, rotate PUSH knob (6) to
Frequency range:
Press PUSH knob (6) to change the stepping.
5) MONITOR GAIN VOLUME
Set
the OUTPUT VOLUME LEVEL of the microphone in your own speaker.
] menu, rotate PUSH knob (6) to
At [
There are 32 levels. "OFF"
6) TOT (Time Out Timer)
Set
the TOT. If the PTT pedal (23) is pressed for more than "TOT" time, the
transmission ends.
At [
] menu, rotate PUSH knob (6) to
tion. Time range 3
7) SWR PROTECTION
Enable/disable
the SWR PROTECTION.
At [
] menu, rotate PUSH knob (6) to
protection. Default: "
and exit.
8) SWR PROTECTION SETTING
Set
the SWR LEVEL PROTECTION.
At [
] menu, rotate PUSH knob (6) to
Level range:
~ 2
12
the step. The SWR level is useful only in the SWR protection function is active.
Hz.
050
9) VOLTAGE PROTECTION
Enable/disable
VOLTAGE PROTECTION.
At [
] menu, rotate PUSH knob (6) to
the protection. Default: "
10) VOLTAGE PROTECTION HIGH
Set
the HIGHER LIMIT of VOLTAGE PROTECTION.
35
set
the Frequency.
Hz ~ 3
Hz, stepping frequency:
300
000
set
the Frequency.
Hz ~ 3
Hz, stepping frequency:
300
000
set
the Monitor volume level.
disable
the function.
set
the TOT, "
~ 60
s, time stepping: 3
s, default: 18
0
0
0
enable
"
".
set
the protection Level.
. Press PUSH knob (6) to change
, stepping:
, default: 2
00
1
00
enable
".
Hz, default:1
Hz.
10
050
Hz, default:1
Hz.
10
050
"
disable
the func-
s.
0
" or
disable
"
" the
"
" or
disable
"
"
Publicité
Table des Matières
