Preliminary Checks; Control Panel - Dantherm ACD 137 Manuel D'utilisation Et De Maintenance

►►►4. START-UP
►►4.1. PRELIMINARY CHECKS
CAUTION: Check that the power cord is
properly connected.
CAUTION: Check that all the cover pan-
els are in the correct position and are locked via
fixing screws before commissioning.
►►4.2. CONTROL PANEL
(PIC. 4)
The unit is equipped with a luminous control pan-
el, which indicates the operating status of the ap-
pliance.
A brief description is provided below:

CONTROL PANEL:

►[ - - ] (SHOWN ON THE DISPLAY): The display
shows [ - - ] when the unit is connected to the
mains and electrically powered.
LED:
►FAN SPEED LED: These LEDs indicate the set
ventilation speed (LOW > Low speed / HIGH >
High speed).
►ALARM LED: This LED is on when the unit is in
alarm. The display will show the error message.
►MODE LED: These LEDs indicate the selected
operating mode:
-COOL LED: This LED indicates that the appli-
ance is operating in "COOLING" mode.
This LED flashes during defrosting or if the tem-
perature set point is reached.
-LED DRYER: This LED indicates that the ap-
pliance is operating in "DEHUMIDIFICATION"
mode.
This LED flashes during defrosting or if the hu-
midity set point is reached.
-LED FAN: This LED indicates that the appli-
ance is operating in "VENTILATION" mode.
BUTTONS:
►ON/OFF: Press "ON/OFF" to turn the appliance
on.
Press the "ON/OFF" button to turn the appliance
off (with the appliance off, the display shows [ - -
]).
NOTE: When the appliance is turned off and
then on immediately, the compressor does not
start immediately. After a few minutes, the appli-
ance restarts automatically.
►FAN SPEED: Press the "FAN SPEED" button
to select the desired ventilation speed (LOW >
Low Speed / HIGH > High Speed).
►SET "▼" / "▲" (SET POINT): By pressing the
SET "▼" / "▲" buttons it is possible to set the
desired set point value. The display will start
flashing, showing the new reference set point.
After a few seconds the display stops flashing
and the new set point has been detected by the
electronics.
It is possible to operate the appliance regard-
less of the degree of temperature or humidity in
the environment; in fact, the appliance will work
continuously while pressing the "▼" button until
"CONT" appears on the display.
►MODE: Press the "MODE" button to select the
desired operating mode:
●●COOLING MODE (PIC. 5) [COOL MODE]: Se-
lect the "COOL" cooling mode on the control
panel.
●●COOLING MODE WITH DUCTING (PIC. 6-7)
[COOL MODE]:
○I° - Duct the hot air from the upper grid (C PIC.
2) to outside the room.
○II° - Select the "COOL" cooling mode on the
control panel.
●●DEHUMIDIFICATION MODE (PIC. 8) [DRYER
MODE]: Select the "DRYER" dehumidification
mode on the control panel.
►HOURS/TAC: Press the "HOURS/TAC" button
to view the working HOURS/TAC of the appli-
ance.
►►4.3. DISCHARGE PIPE CONNEC-
TION (Set-up)
A discharge pipe can be connected to the appli-
ance. Remove the tank and connect a fixed pipe
to the condensate drain (3/4" male fitting).
►►4.4. CONNECTING AIR DUCTING
PIPES
Air ducting pipes can be connected to the ap-
pliance. It is recommended to use only pipes of
adequate section and to avoid bends or narrow-
ing of the duct sections.
It is forbidden to move the appliance when it is
ON and when it is connected to ducting pipes.
en
it
de
es
fr
nl
pt
da
fi
no
sv
pl
ru
cs
hu
sl
tr
hr
lt
lv
et
ro
sk
bg
uk
bs
el
zh