Technical Data; General Warnings - Rupes FR32ES Conversion Des Instructions De Fonctionnement Original

TECHNICAL DATA

TYPE
INSULATION CLASS
ABSORBED POWER W
n NOMINAL RPM
ELECTRONIC SPEED CONTROL
Ø MAX B ACKING PAD OR POLISHING FOAM
SPINDLE THREAD
WEIGHT Kg according to EPTA-Procedure 01/2003
The values shown are based on a nominal voltage of 230V/50Hz. In the case of voltages and frequencies of different power values may vary.
Refer to the label technical specifications to the nominal values of the tool.

GENERAL WARNINGS

All instructions concerning safety and the prevention of industrial accidents
can be found in file SAFETY INSTRUCTIONS, that forms integral part of this
documentation. This INSTRUCTION MANUAL only contains additional
information that specifically explain how to use the machine.
SPECIFIC USE
This tool is designed to be used as a polisher. Read all the warnings,
instructions, indications provided on drawings and specifications supplied
with this tool. Failure to comply with all the instructions provided below may
cause electrical shocks, fire and/or serious injuries.
This tool is not intended to be used for smoothing, metal brushing and
cutting operations. The use of this tool for unintended applications may cause
hazards and injuries to people.
The tool must be used with accessories that have been specifically
designed or recommended by the manufacturer. The fixing of the accessory
to the tool does not guarantee a safe operation.
Do not use accessories that are not specifically designed for the intended
use of the tool or that have not been recommended by the manufacturer.
The fact that an accessory can be fixed to the tool does not imply that it can be
used safely.
The rated speed of accessories must be at least equivalent to the maximum
speed of the tool. If operated at a greater speed than the rated one,
accessories may break and cause the ejection of chips.
The external diameter and thickness of accessories must be appropriate to
guarantee the protection and safety of the tool. Accessories with incorrect
dimensions cannot be adequately protected or controlled.
The configuration of the cutting/grinding wheels or any other accessory
mustperfectly adapt to the tool spindle. Accessories with holes that cannot be
aligned with the fitting components on the tools will cause unbalance, excessive
vibrations and may be difficult to control.
8
Do not use an accessory if damaged. Before use, inspect all the accessories,
like the abrasive cutting/grinding wheels, in order to verify that they are not
cracked or splintered. If the tool or accessory has fallen, verify that they are
not damaged and, if necessary, replace it with a new one. After inspecting
or installing an accessory, move to a safe distance with any other person
present and operate the tool at maximum speed without load for one minute.
Damaged accessories generally break during this test period.
Wear personal protective equipment. According to the the application, use
face shield, mask or safety goggles. According to the case, wear a dust
mask, ear protection, gloves and a smock capable of stopping small abrasive
fragments of the work piece. Eye protection must be able to stop flying bits
produced from the different operations The dust mask or the respirator must be
capable of filtering particles produced by your work. Prolonged exposure to high
intensity noise can cause a loss of hearing.
Keep the people present at a safety distance with respect to the work area.
Anyone entering the work area must wear personal protection equipment.
The fragments of the work piece or the broken accessories can fly off and cause
injuries in the immediate vicinity of the work area.
Keep the tool only for isolating gripping surfaces, while the operations are
carried out in which the cutting accessory may be in contact with the hidden
cables or with its cable. The contact between the cutting accessory and the
cable "under voltage" can also put the exposed metal parts of the electrical tool
"under voltage" and can cause an electrical shock for the operator.
Position the cable far from the rotation accessory. If control is lost, the cable
can be cut or twisted and your hand or arm could be pulled into the rotation
accessory.
Never put the electrical tool back before the accessory has completely
stopped. The rotation accessory can be pressed on the surface with the electrical
tool put out of your control.
Do not operate the electrical tool while carrying it at the side. Accidental
contact with the rotation accessory can get your clothes entangled and attract
FR32ES
/ II
900
1500-4000
YES
75
M14
1,9