Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
TECHNICAL DATA
MODEL
Ø POLISHING FOAM mm
Ø BACKING PAD mm
Ø ORBIT mm
POWER W
R.P .M.
WEIGHT kg
SPEED CONTROL
PROTECTION CLASS
OPERATING VOLTAGE
ABSORBED CURRENT
LHR21ES
6
9
7
4
INTENDED USE
The LHR21ES and LHR15ES heavy-duty polishers is designed
for polishing painted or unfinished metal, fiberglass, and com-
posite surfaces in professional applications. Common examples
of use include but are not limited to: auto/marine/RV/motorcycle
detailing and finish correction, boat construction and repair, and
metal finishing.
Do not use in the presence of flammable liquids or gases.
Do not let children come into contact with the tool. Supervision
is required when inexperienced operators use this tool.
MOTOR
Be sure your power supply agrees with the voltage marked on
the nameplate. 120 Volts AC 60Hz means alternating current
only. Voltage decrease of more than 10% will cause loss of
power and overheating.
PARTS OF THE TOOL
1 - Identification plate
2 - ON/OFF switch
3 - Electronic speed control
4 - Back-up pad fixing screw
5 - Back-up pad Allen wrench
6 - Handle
7 - Polishing mop (not supplied)
8 - Handle fixing screws
9- Velcro faced back-up pad
10 - Motor ventilation slots
11 - Switch locking button
ON/OFF SWITCH
WARNING: To reduce the risk of injury, make sure the
polisher is not resting on the workpiece when the switch
is turned on.
To turn the polisher on, push the lever of the switch (2) towards
the body of the tool; if the polisher is to be locked in ON position,
press button (11) at the same time and keep it pressed while
releasing lever, thus locking the switch.
10
3
2
11
8
1
5
LHR15ES
6
9
7
4
To turn the polisher off, release the lever or, if locked in ON
position, push the lever to release the lock button.
ELECTRONIC SPEED CONTROL
The polisher electronic speed control supply the following fea-
tures.
Speed setting
The speed of the polisher can be set by rotating the speed dial
(3) to the desired setting for any speed between 2000 and 4200
r.p.m. (LHR21ES), between 2000 and 4800 r.p.m. (LHR15ES).
Speed compensation
In case of overloading the polisher, the electronic speed control
will compensate and maintain the selected speed till a safe level.
Exceeding this overload level may result in strong vibrations and
tool overtemperature.
Starting acceleration ramp
To avoid kickback effect and compound splattering, the
electronic speed control always supply a smooth starting
acceleration ramp when the tool is turned on.
Accidental re-start protection
In case of a sudden lack of main power supply, the electronic
speed control prevents the re-start after the power supply
restoring if the main switch is turned on. The polisher must be
turned off and on again pushing the lever of the switch (2)
toward the body of the tool.
OPERATION
WARNING: To reduce the risk of injury, turn unit off and
disconnect it from power source before installing and
removing accessories, before adjusting or when making
repairs. Be sure the switch is in the "OFF" position. An
accidental start-up can cause injury
WARNING: Never modify any parts of the power tool.
Damage or personal injury could result.
ENGLISH
LHR21ES
LHR15ES
180
150
21
500
2000 ÷4200
2000 ÷4800
2,6
•
II
120 V AC - 60 Hz
120 V AC - 60 Hz
4 A
10
3
2
11
8
1
5
150
125
15
500
2,6
•
II
4 A
Publicité
Table des Matières
