Assembly/Replacement Of Accessoires Assembly - Rupes FR32ES Conversion Des Instructions De Fonctionnement Original

ASSEMBLY/REPLACEMENT OF MOUSSE DISK
ASSEMBLY
- Screw the mousse disk (9) on the spindle (10).
- screw the mousse disk on the tapered ring nut and tighten it using the pin
spanner, preventing the spindle from moving using the wrench (7).
REPLACEMENT
- Lock the spindle shaft with a wrench (7);
- Unscrew the mousse disk.
No other tools for tightening / loosening.
ASSEMBLY/REPLACEMENT OF ACCESSOIRES
ASSEMBLY
Apply pressure on polishing pad to join pad to plate.
REPLACEMENT
Remove the polishing foam used and apply the new one with pressing on the
backing pad.
STARTING AND STOPPING
- Starting: push the slide of the ON/OFF (2) forward; if the tool is to be locked in
the ON position, apply pressure to the front part of the slide switch at the same
time.
- Stopping: release the slide ON/OFF (2).
If locked, press the ON/OFF switch in the lower part downwards and release it
in the OFF position.
WARNING: after an interruption of the electrical energy, if the
ON/OFF switch is inserted, it is necessary to release the switch
(see Stopped).
ELECTRONIC RPM REGULATION
The rpm can be adjusted by rotating the speed adjustment wheel(3) located on
the rear of the tool. The choice of speed depends on the characteristics of the
abrasive paper disc and the material to be worked.
ACCESSORIES
Buffers up to 75 mm Ø.
MAINTENANCE
All maintenance operations are carried out with the power supply
disconnected. At the end of each work session, or when required,
remove any dust from the body of the tool using a jet of compressed air,
paying particular attention to the motor ventilation slots.
No other maintenance operations must be undertaken by the user.
Maintenance and cleaning of the inner parts, like brushes, ball bearings, gears
etc. or others, must be carried out only by an authorized customer-service
10
workshop or on www.rupes.com.
Use only the original RUPES parts or accessories.
DISPOSAL
For EC countries only: According to the European Directive on Waste
from electrical and electronic equipment and its implementation in
conformity with national standards, exhausted electrical equipment
must be collected separately, in order to be recycled in an
environmentally friendly way. The product, when it reaches the end of its life, must
not be dispersed in the environment or thrown away as household waste. It must
be disposed at authorized recycling centres (contact your local authorities to
know where to dispose of the product according to the law). The correct disposal
of the product contributes to the health and preservation of the environment.
Illegal disposal of the product will entail penalties against the offenders.
Disposing of the product correctly contributes to protecting human health and
safeguarding the environment. Any illegitimate disposal of the product will be
punishable by law.
CONFORMITY DECLARATION
We declare on our responsability that the hand-held motor operated tool, which
is mentioned in the present operating manual, is in comformity with the Essential
Requirements of Safety of the following Directives:
2006/42/EU; 2014/35/EU; 2014/30/EU; 2011/65/EU
The tests have been carried out in accordance with following Standards:
EN 60745-1:2009 + A11:2010
EN 60745-2-3:2011 + A2:2013 + A11:2014 + A12:2014 + A13:2015
EN 55014-1:2006 + A1:2009 + A2:2011
EN 55014-2:1997 + A1:2001 + A2:2008
EN 61000-3 -2:2006 + A1:2009 + A2:2009
EN 61000-3-3:2013
EN 62233:2008
Technical file at:
RUPES S.p.A.
Via Marconi, 3A
20080 VERMEZZO (Mi) - Italy
Vermezzo (MI), 22/06/2016
S.p.A
IL PRESIDENTE
G. Valentini