Ambient Conditions; Electrical Specifications - Benning MM 1 Notice D'emploi

height and automatic decimal point placement. The highest display
value is 3200.
5.1.2 The polarity display  is automatic. As positive is implied by the
defined input terminal, only a negative pole will be indicated with "-".
5.1.3 Overranging is indicated by a blinking "1" or "-1" and the buzzer
sounds.
5.1.4 The range selection button "RANGE"  allows the user to change the
range manually and causes the "RANGE" annunciator to appear on
the LCD display. Hold the switch for 2 seconds to return to the auto-
matic ranging function ("RANGE" annunciator disappears from the
display). In the rotary switch position
between the functions continuity test and diode test by means of the
"RANGE" key .
5.1.5 Measurement values are saved by pressing the "HOLD" button . The
"H" annunciator appears on the display. By pressing the button again
the tester returns into measurement mode.
5.1.6 The nominal measuring rate of the BENNING MM 1 display is approx.
2 measurements per second. The bar graph measuring rate is approx.
12 measurements per second.
5.1.7 The BENNING MM 1 is turned on and off using the rotary switch .
Unit is turned off when switch is in "OFF" position.
5.1.8. The BENNING MM 1 is automatically switched off after 10 min. You
can switch it on again by means of the "RANGE" key .
5.1.9 Temperature coefficient of the measurement reading: 0.15 x (given
accuracy)/ °C , < 18 °C or > 28 °C.
5.1.10 The BENNING MM 1 is powered by two 1.5 V batteries (IEC LR03/
"Micro").
5.1.11 When the battery voltage drops below the operating voltage of the
BENNING MM 1 a low battery symbol appears on the display.
5.1.12 The lifespan of a battery is approx. 1000 hours (Alkaline battery).
5.1.13 Meter dimensions:
(L x W x H) = 155 x 80 x 26 mm without protective rubber holster
(L x W x H) = 165 x 80 x 36 mm with protective rubber holster
Meter weight:
170 g without protective rubber holster
310 g with protective rubber holster
5.1.14 The safety test leads provided with the meter are specifically suited for
the rated voltage and current of the BENNING MM 1. The probe tips
can be covered with protective caps.
5.1.15 The BENNING MM 1 is protected from mechanical damage by a pro-
tective rubber holster . The protective rubber holster  allows the
BENNING MM 1 to be placed upright or hung up during measuring.
6.

Ambient conditions

- The BENNING MM 1 is designed for measuring in dry conditions,
- Altitude during measuring: 2000 m maximum
- Overvoltage category/ Location category: IEC 60664-1/ IEC 61010-1 →
600 V category III,
- Pollution degree: 2,
- Protection Class: IP 30 (DIN VDE 0470-1 IEC/ EN 60529)
IP 30 means: Protection against access to dangerous parts and protection
against solid impurities of a diameter > 2.5 mm, (3 - first index). No protec-
tion against water, (0 - second index).
- Working temperature and relative humidity:
for working temperature between 0 °C and 30 °C: relative humidity smaller
than 80 %
for working temperature between 30 °C and 40 °C: relative humidity smaller
than 75 %
for working temperature between 40 °C and 50 °C: relative humidity smaller
than 45 %
- Storage temperature: the BENNING MM 1 can be stored at temperatures
between - 20 °C and + 60 °C. The battery should be removed when tester
is in storage.
7.

Electrical specifications

Note: measurement accuracy is given as the sum of
- a relative percentage of the reading and
- the number of least significant digits
This accuracy is valid for temperatures between 18 °C and 28 °C, with a relative
humidity smaller than 75 %.
09/ 2013
BENNING MM 1
, it is possible to change

10