Wiring Instructions - Eaton CROUSE-HINDS Serie Guide Rapide

Pendant Mounting (Cable)
1. Remove cover from enclosure and let hang by safety chain.
2. Remove fixture from conduit and set aside.
3. Install conduit T onto conduit and install pipe nipple into vertically facing T
leg.
4. Install gland into horizontal facing pipe nipple.
5. Install conduit T onto conduit and install pipe nipple into vertically facing T
leg.
6. Install glands into horizontal facing pipe nipples.
7 . Install glands into sensor hubs.
8. Locate installation location and secure the L -brackets to the wall with
customer supplied hardware.
9. Secure L-brackets to the enclosure with included hardware. Torque the
hardware to 25 in-lbs. (The enclosure provides 4 thru holes at the corners
for mounting L-brackets.) Note: Sensor lens must face down when
installed and have an unobstructed view.
10. Once wired (see wiring instructions), replace the cover and torque the
provided cover screws with 0-rings until fully seated.
11. Re-install fixture to conduit T.
Stanchion Mounting
1. Remove cover from enclosure and let hang by safety chain.
2. Remove Stanchion mount from pole and set aside.
3. Install conduit T onto top of pole and install pipe nipple into vertically
facing T leg.
4. Install gland into horizontal facing pipe nipple.
5. Install conduit T onto pipe nipple and install pipe nipple into vertically
facing T leg.
6. Install glands into horizontal facing pipe nipples.
7 . Install glands into sensor hubs.
8. Locate installation location and secure the U-bolts and Stanchion Mount
Brackets to the Stanchion pole using included hardware. Torque the
hardware to 138 in-lbs.
9. Secure the L-brackets to the Stanchion Mount Brackets using the included
hardware. Torque the hardware to 25 in-lbs.
10. Secure L-brackets to the enclosure with included hardware. Torque the
hardware to 25 in-lbs. (The enclosure provides 4 thru holes at the corners
for mounting L-brackets.) Note: Sensor lens must face down when
installed and have an unobstructed view.
11. Once wired (see wiring instructions), replace the cover and torque the
provided cover screws with 0-rings until fully seated.
12. Re-install Stanchion mount to conduit T.
All statements, technical information and recommendations contained herein are based on information and tests we believe to be reliable. The accuracy or completeness thereof are not
guaranteed. In accordance with Eaton's Crouse-Hinds Division's "Terms and Conditions of Sale," and since conditions of use are outside our control, the purchaser should determine
the suitability of the product for his intended use and assumes all risk and liability whatsoever in connection therewith.
Eaton's Crouse-Hinds Division
1201 Wolf Street Syracuse, NY 13208 • U.S.A.
Copyright© 2022

WIRING INSTRUCTIONS

120/277 VAC
NEUTRAL
LOAD
16-18 AWG Solid CU
Wire Only
FSP-211 FSP-211
v2
High/Low PIR
Occupancy Sensor
Dimming
230-240V~, 50/60 Hz
300W max ballast
5E4, 40T75
Driver
LISTE D
Appliance
Contro l
88T9
E101196
120V/277V, 50/60 Hz: UL/cUL
800W/1200W Max Tungsten,
Ballasts or LED Driver
1/6 HP
www.legrand.us/wattstopper
18-20 AWG Solid CU Wire Only
PINK (-)
PURPLE (+)
FSP-211 wiring with dimming
ballast or LED driver
OPERATING INSTRUCTIONS
For detailed operating instructions consult WattStopper FSP-211 data sheet.
For instructions for selecting custom settings consult WattStopper FSIR-100
Wireless IR Commissioning Tool data sheet.
NEUTRAL
LOAD
16-18 AWG Solid CU
Wire Only
FSP-211 FSP-211
v2
High/Low PIR
Occupancy Sensor
Non-Dimming 230-240V~, 50/60 Hz
300W max ballast
5E4, 40T75
Driver
LISTE D
Appliance
Contro l
88T9
E101196
120V/277V, 50/60 Hz: UL/cUL
800W/1200W Max Tungsten,
Ballasts or LED Driver
1/6 HP
www.legrand.us/wattstopper
18-20 AWG Solid CU Wire Only
FSP-211 wiring with
non-dimming ballast or LED driver
Revision 2
Revised 12/22
Supersedes 02/15
IF 1744