Table des Matières
Publicité
• Keep children and bystanders away while operating a
power tool . Distractions can cause you to lose control .
Electrical safety
• Power tool plugs must match the outlet . Never modify
the plug in any way . Do not use any adapter plugs with
earthed (grounded) power tools . Unmodified plugs and
matching outlets will reduce risk of electric shock .
• Avoid body contact with earthed or grounded surfaces,
such as pipes, radiators, ranges and refrigerators . There is
an increased risk of electric shock if your body is earthed
or grounded .
• Do not expose power tools to rain or wet conditions . Wa-
ter entering a power tool will increase the risk of electric
shock .
• Do not abuse the cord . Never use the cord for carrying,
pulling or unplugging the power tool . Keep cord away
from heat, oil, sharp edges and moving parts . Damaged
or entangled cords increase the risk of electric shock .
• When operating a power tool outdoors, use an extension
cord suitable for outdoor use . Use of a cord suitable for
outdoor use reduces the risk of electric shock .
• If operating a power tool in a damp location is unavoida-
ble, use a residual current device (RCD) protected supply .
Use of an RCD reduces the risk of electric shock .
Personal safety
• Stay alert, watch what you are doing and use common
sense when operating a power tool . Do not use a power
tool while you are tired or under the influence of drugs,
alcohol or medication . A moment of inattention while
operating power tools may result in serious personal
injury .
• Use personal protective equipment . Always wear eye
protection . Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal in-
juries .
• Prevent unintentional starting . Ensure the switch is in
the off-position before connecting to power source and/
or battery pack, picking up or carrying the tool . Carrying
power tools with your finger on the switch or energising
power tools that have the switch on invites accidents .
• Remove any adjusting key or wrench before turning the
power tool on . A wrench or a key left attached to a rotat-
ing part of the power tool may result in personal injury .
• Do not overreach . Keep proper footing and balance at
all times . This enables better control of the power tool in
unexpected situations .
• Dress properly . Do not wear loose clothing or jewellery .
Keep your hair, clothing and gloves away from moving
parts . Loose clothes, jewellery or long hair can be caught
in moving parts .
• If devices are provided for the connection of dust extrac-
tion and collection facilities, ensure these are connected
and properly used . Use of dust collection can reduce
dust-related hazards .
Power tool use and care
• Do not force the power tool . Use the correct power tool
for your application . The correct power tool will do the
job better and safer at the rate for which it was designed .
• Do not use the power tool if the switch does not turn it
on and off . Any power tool that cannot be controlled with
the switch is dangerous and must be repaired .
• Disconnect the plug from the power source and/or the
battery pack from the power tool before making any ad-
justments, changing accessories, or storing power tools .
Such preventive safety measures reduce the risk of start-
ing the power tool accidentally .
• Store idle power tools out of the reach of children and do
not allow persons unfamiliar with the power tool or these
instructions to operate the power tool . Power tools are
dangerous in the hands of untrained users .
• Maintain power tools . Check for misalignment or bind-
ing of moving parts, breakage of parts and any other
condition that may affect the power tool's operation . If
damaged, have the power tool repaired before use . Many
accidents are caused by poorly maintained power tools .
• Keep cutting tools sharp and clean . Properly maintained
cutting tools with sharp cutting edges are less likely to
bind and are easier to control .
• Use the power tool, accessories and tool bits etc . in ac-
cordance with these instructions, taking into account the
working conditions and the work to be performed . Use
of the power tool for operations different from those in-
tended could result in a hazardous situation .
Battery tool use and care
• Recharge only with the charger specified by the manu-
facturer . A charger that is suitable for one type of battery
pack may create a risk of fire when used with another
battery pack .
• Use power tools only with specifically designated battery
packs . Use of any other battery packs may create a risk of
injury and fire .
• When battery pack is not in use, keep it away from other
metal objects, like paper clips, coins, keys, nails, screws
or other small metal objects, that can make a connection
from one terminal to another . Shorting the battery termi-
nals together may cause burns or a fire .
• Under abusive conditions, liquid may be ejected from
the battery; avoid contact . If contact accidentally occurs,
flush with water . If liquid contacts eyes, additionally seek
medical help . Liquid ejected from the battery may cause
irritation or burns .
9
Publicité
Table des Matières
