Optional Accessories - Makita DBO140 Manuel D'instructions

Removing dust box and paper filter bag
(Fig. 10 & 11)
Remove the dust nozzle by pushing the two latches.
Remove the paper filter bag first by pinching the logo
side of its cardboard lip, then by pulling the cardboard lip
downwards to move it out of the holding tab of the dust
box.
Removing and reinstalling the skirt
(Fig. 12, 13 & 14)
CAUTION:
• Do not use the tool without the skirt. Otherwise dust is
scattered all over.
You can choose one of 12 directions of the skirt in accor-
dance with your purpose.
To remove the skirt, remove the screw and remove the
skirt with slightly opening it for both sides.
To reinstall the skirt, install it with slightly opening it for
both sides. And fasten the screw.
CAUTION:
• Do not set the skirt other than the designated angle.
Otherwise the tool may be damaged.
OPERATION
WARNING:
• Never switch on the tool when it is in contact with the
workpiece, it may cause an injury to operator.
Sanding operation (Fig. 15)
CAUTION:
• Never run the tool without the abrasive disc. You may
seriously damage the pad.
• Never force the tool. Excessive pressure may decrease
the sanding efficiency, damage the abrasive disc or
shorten tool life.
• Using the tool with the pad edge contacting the work-
piece may damage the pad.
Hold the tool firmly. Turn the tool on and wait until it
attains full speed. Then gently place the tool on the work-
piece surface. Keep the pad flush with the workpiece and
apply slight pressure on the tool.
CAUTION:
• The sanding pad rotates clockwise during the loaded
operation, but it may rotate counterclockwise during the
no-load operation.
Polishing operation (optional)
CAUTION:
• Use only a Makita genuine sponge pad, felt pad or wool
pad (optional accessories).
• Always operate the tool at low speed to prevent work
surfaces from heating abnormally.
• Never force the tool. Excessive pressure may decrease
the polishing efficiency and cause motor overload,
resulting in tool malfunction.
1. Applying wax (Fig. 16)
Use an optional sponge pad. Apply wax to the
sponge pad or work surface. Run the tool at low
speed to smooth out wax.
NOTE:
• First, wax a not conspicuous portion of the work sur-
face to make sure that the tool will not scratch the sur-
face or result in uneven waxing.
8
• The tool starts with high speed mode. Be careful when
you start the tool. The wax may be spattered. It is rec-
ommended that you spread wax with the tool stopped
before starting up the tool. Change the speed mode to
low immediately after you start the tool.
• Always run the tool at low speed. Running it at high
speed may cause the wax to spatter.
2. Removing wax (Fig. 17)
Use an optional felt pad. Run the tool at low speed
to remove wax.
3. Polishing (Fig. 18)
Use an optional wool pad. Run the tool at low speed
and apply the wool pad gently to the work surface.
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off and the bat-
tery cartridge is removed before attempting to perform
inspection or maintenance.
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
To maintain product SAFETY and RELIABILITY, repairs,
carbon brush inspection and replacement, any other
maintenance or adjustment should be performed by
Makita Authorized Service Centers, always using Makita
replacement parts.

OPTIONAL ACCESSORIES

CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Hook-and-loop type abrasive discs (with pre-punched
holes)
• Hook-and-loop type sponge pad
• Hook-and-loop type felt pad
• Hook-and-loop type wool pad
• Makita genuine battery and charger
• Dust box
• Paper filter bag
• Dust bag
NOTE:
• Some items in the list may be included in the tool pack-
age as standard accessories. They may differ from
country to country.
Noise
The typical A-weighted noise level determined according
to EN62841-2-4:
Model DBO140
Sound pressure level (L
Uncertainty (K): 3 dB (A)
The noise level under working may exceed 80 dB (A).
Model DBO180
Sound pressure level (L
Uncertainty (K): 3 dB (A)
The noise level under working may exceed 80 dB (A).
ENG905-1
): 78 dB (A)
pA
): 77 dB (A)
pA