! before switching off the tool, you should lift it
from the workpiece
! the accessory continues to rotate for a short time
after the tool has been switched off
• Grinding 8
- move the tool back and forth with moderate pressure
! never use a cutting disc for side grinding
• Cutting 9
- do not tilt the tool while cutting
- always move the tool in same direction as arrow on
tool head, in order to prevent the tool from being
pushed out of the cut in an uncontrolled manner
- do not apply pressure on the tool; let the speed of the
cutting disc do the work
- do not brake cutting discs with side pressure
• Holding and guiding the tool
- always hold the tool firmly with both hands, so you will
have full control of the tool at all times
! while working, always hold the tool at the
grey-coloured grip area(s) 0
- provide for a secure stance
- pay attention to the direction of rotation; always hold
the tool so, that sparks and grinding/cutting dust fly
away from the body
- keep ventilation slots K 2 uncovered
MAINTENANCE / SERVICE
• Always keep tool and cord clean (especially ventilation
slots K 2)
! do not attempt to clean ventilation slots by
inserting pointed objects through openings
! disconnect the plug before cleaning
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skilmasters.com)
ENVIRONMENT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2012/19/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol ! will remind you of this when the need for
disposing occurs
DECLARATION OF CONFORMITY
Angle grinder 1049
Technical data 1
• We declare under our sole responsibility that the product
described under "Technical data" is in conformity with the
following standards or standardization documents: EN
60745, EN 61000, EN 55014, in accordance with the
provisions of the directives 2004/108/EC, 2006/42/EC,
2011/65/EU
• Technical file at: SKIL Europe BV (PT-SEU/ENG1),
4825 BD Breda, NL
24.04.2014
NOISE/VIBRATION
• Measured in accordance with EN 60745 the sound
pressure level of this tool is 99 dB(A) and the sound
power level 110 dB(A) (standard deviation: 3 dB), and the
vibration ✱ (hand-arm method; uncertainty K = 1.5 m/s²)
✱ when surface grinding 6.5 m/s²
✱ when sanding 3.1 m/s²
! other applications (such as cutting-off or wire
brushing) may have different vibration values
• The vibration emission level has been measured in
accordance with a standardised test given in EN 60745; it
may be used to compare one tool with another and as a
preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for different applications, or with different
or poorly maintained accessories, may significantly
increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may significantly
reduce the exposure level
! protect yourself against the effects of vibration
by maintaining the tool and its accessories,
keeping your hands warm, and organizing your
work patterns
Meuleuse d'angle
INTRODUCTION
• Cet outil sert au meulage, au tronçonnage et à l'ébarbage
de pièces en métal et en pierre sans utiliser de l'eau;
combiné avec des accessoires spécifiques, cet outil peut
également servir au brossage et au ponçage
• Les opérations de coupe avec disques à tronçonner
abrasifs ne sont autorisées que si une protection de
tronçonnage (disponible en option comme
accessoire SKIL 2610Z00992) est utilisée
• Lisez et conservez ce manuel d'instruction 3
10
1049