Kettler SPRINTER 5 Instructions De Montage page 5

Assembly Instructions
I In case of a regular use of the running belt, the cold running belt
has to be serviced with silicone oil.
I Depending on the degree of use and load to which the unit is
subjected, the belt may tend to stretch or slip. Tighten the belt as
described. Adjust the tightness of the belt as described in section
„handling".
I Observe the movement of the edge of the belt when it is in use. If
it tends to run towards the side, readjust it accordingly.
Care and Maintenance
I Do not use corrosive or abrasive materials to clean the equip-
ment. Ensure that such materials are not allowed to pollute the
environment.
I The electrical elements and components do not require special
maintenance. No alterations or repairs (except mantainance
checks) should be made to these parts unless by a qualified
electrician.
I When ordering spare parts, always state the full item number,
spare-part number, the quantity required and the serial number
of the product.
Example order: Art. no. 07880-200 / spare-part no. 68006686/
1 pieces / serial no......
Instructions for Assembly
I Ensure that you have received all the parts required (see check
list) and that they are undamaged. Should you have any cause
for complaint, please contact your KETTLER dealer.
I Before assembling the equipment, study the drawings carefully
and carry out the operations in the order shown by the dia-
grams. The correct sequence is given in capital letters.
I The equipment must be assembled with due care by an adult
person. If in doubt call upon the help of a second person, if
possible technically talented.
I Please note that there is always a danger of injury when wor-
king with tools or doing manual work. Therefore please be
careful when assembling this machine.
I Ensure that your working area is free of possible sources of dan-
ger, for example don't leave any tools lying around. Always
dispose packaging material in such a way that it may not cause
any danger. There is always a risk of suffocation if children play
with plastic bags!
Handling
Belt adjustment (picture 6):
Adjust the belt while running it at a speed of about 6 km/h (if
necessary, less). No person must be on the belt while adjusting
it!
If the belt moves to the right, carefully turn the right adjusting
screw clockwise by max. a quarter of a rotation with the enclo-
sed socket spanner. Operate the belt and check the course of the
belt. Repeat this process until the belt runs straight away.
If the belt moves to the left, carefully turn the right adjusting screw
counter-clockwise by max. a quarter of a rotation with the
enclosed socket spanner. Operate the belt and check the course
of the belt. Repeat this process until the belt runs straight away.
Belt straightening:
Turn the adjusting screw to the right by max. one turn. Repeat
this process on the other side. Check as to whether the conti-
Running Tip:
Running straight on the treadmill is made easier by
focussing on a fixed object in front of you in the
room. Run as if you wanted to approach the object.
Importantly:
Please keep the safety key in a safe place and ensu-
re that it is kept out of reach of children!
Important: spare part prices do not include fastening material; if
fastening material (bolts, nuts, washers etc.) is required, this
schould be clearly stated on the order by adding the words „with
fastening material".
Waste Disposal
KETTLER products are recyclable. At the end of its use-
ful life please dispose of this article correctly and safe-
ly (local refuse sites).
DE 60229750
I The fastening material required for each assembly step is shown
in the diagram inset. Use the fastening material exactly as
instructed. The required tools are supplied with the equipment.
I Bolt all the parts together loosely at first, and check that they
have been assembled correctly. Then use spanner to finally tigh-
ten screws/nuts
I Please keep original packaging of this article, so that it may be
used for transport at a later date, if necessary. Goods may only
be returned after prior arrangement and in (internal) packaging,
which is safe for transportation, in the original box if possible.
It is important to provide a detailed defect description / dama-
ge report!
I For technical reasons, we reserve the right to carry out prelimi-
nary assembly work (e.g. addition of tubing plugs).
nuous belt slips. If this is the case, repeat the described process
once again.
Be very careful when adjusting and straightening the belt. An
extreme over- or under-tension may damage the running belt!
KETTLER GB Ltd.
GB
www.kettler.co.uk
KETTLER International Inc.
USA
www.kettlerusa.com
GB
5