Hilti AIC 1000 Notice D'utilisation Originale page 15

▶ Use the right product for the job. Do not use the product for purposes for which it was not
intended. Use it only as directed and when in faultless condition.
▶ Before beginning work with the product, find out how to operate it correctly and about any hazards
associated with the materials it will be inducting and how these materials can be disposed of.
▶ Take the influences of the surrounding area into account. Do not use the product where there is a
risk of fire or explosion.
▶ Only persons who are familiar with it, who have been trained on how to use it safely and who
understand the resulting hazards are permitted to use the tool. The tool is not intended for use by
children.
▶ Store the product in a secure place when not in use. Products which are not in use must be stored
in a dry, high place or locked away out of reach of children.
2.3 Workplace
▶ Ensure that the workplace is well lit.
▶ Ensure that the workplace is well ventilated. Exposure to dust at a poorly ventilated workplace may
result in damage to the health.
▶ Keep the work area clean and uncluttered and watch out for supply cords routed in the work area.
Carelessly routed supply cords can constitute trip hazards and lead to injuries.
▶ Do not operate the product in explosive atmospheres, such as in the presence of flammable
liquids, gases or dust. Electric appliances cause sparks which may ignite the dust or fumes.
2.4 Electrical safety
▶ The plug on the supply cord of the product must match the outlet. Do not change the plug in any
way. Do not use adapter plugs with earthed (grounded) products. Unmodified plugs and matching
outlets reduce risk of electric shock.
▶ Do not use the product with a damaged supply cord or plug. Return a product with damaged supply
cord or plug to an authorized Hilti service facility for examination and/or repair.
▶ Do not lay the supply cord under carpeting, furniture or other appliances. Do not cover the cord
with throw rugs, runners or similar coverings. Arrange the supply cord away from traffic areas and
ensure that the supply cord does not cause tripping hazards.
▶ Insert the plug in a suitable earthed/grounded power outlet which has been correctly and safely
installed and is in compliance with local regulations. If you are in doubt about the effectiveness of
the power outlet's earth/ground connection, have it checked by a qualified specialist.
▶ Do not expose the product to rain or moisture. Water entering an electric device will increase the risk
of electric shock.
▶ Check to ensure that the supply cord does not lie in a puddle of water.
▶ Check the product's supply cord at regular intervals and have it replaced by Hilti Service if damage
is found. Check extension cords at regular intervals and replace them if found to be damaged.
▶ Do not touch the supply cord or extension cord if they are damaged while working. Disconnect
the supply cord plug from the power outlet. Damaged supply cords or extension cords present a risk
of electric shock.
▶ The electric supply cord may be replaced only with a cord of the type specified in the operating
instructions.
▶ Do not abuse the cord. Never use the cord for carrying, hanging up or unplugging the product.
Keep the cord away from heat, oil, sharp edges and moving parts of the product. Damaged or
entangled cords increase the risk of electric shock.
▶ In the event of an interruption in the electric supply, switch the product off and unplug it from the
power outlet.
▶ Use the power outlet on the product only for the purposes described in the operating instructions.
▶ Never operate the product when it is dirty or wet. Dust (especially dust from conductive materials) or
dampness on the surface of the product may, under unfavorable conditions, lead to electric shock. Have
dirtied or dusty products checked at regular intervals by Hilti Service, especially if they are used
frequently for working on conductive materials.
2.5 Personal safety
▶ Do not use the product where there is asbestos contamination.
*2297300*
2297300 English 11