Install the longer M12 (140mm) bolt and a washer, then the shorter spacer, followed by a shake
proof washer, into bobbin counter bore, place one of the longer spacers over the free end of bolt
and up against bobbin spigot/spacer and tighten bolt until you feel some compression from inside
the protector. PLEASE NOTE BOBBIN MUST BE POSITIONED AS PICTURED ABOVE
WITH BIGGER END TOWARD FRONT OF BIKE. Turn a little more so that you feel the
compression increase slightly. Then apply a quarter turn. Do not overtighten as damage can occur
to the bike. Do not exceed 40nm of torque. Insert bobbin cap so logo is as shown above.
Right-hand side (as you sit on bike)
Remove front side fairing.
Loosen the engine bolt arrowed above right, undo the bolt until head of bolt just contacts inside
edge of fairing when the fairing is refitted.
Paint the head of the bolt with paint or tippex and refit fairing.
Ensure paint has marked the inside face of fairing and remove fairing.
Using pilot drill from a 28mm tank cutter, drill fairing from inside face of fairing central to paint
mark from head of bolt.
Refit fairing to ensure pilot hole is central to engine bolt.
Remove fairing and using pilot hole as guide drill fairing using 28mm tank cutter.
Remove engine bolt ensuring frame to engine spacer does not move (if the spacer is very loose a
dab of super glue on the face may hole it in position).
Refit the fairing.
Install the shorter M12 (100mm) bolt and a washer, then the shorter spacer, followed by a shake
proof washer, into bobbin counter bore, place the remaining longer spacer over the free end of bolt
and up against bobbin spigot/spacer and tighten bolt until you feel some compression from inside
the protector. PLEASE NOTE BOBBIN MUST BE POSITIONED AS PICTURED ABOVE
WITH BIGGER END TOWARD FRONT OF BIKE. Turn a little more so that you feel the
compression increase slightly. Then apply a quarter turn. Do not overtighten as damage can occur
to the bike. Do not exceed 40nm of torque. Insert bobbin cap so logo is as shown above.
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order. The
Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than those
in R&G's order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for
its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify
any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on the
motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its option either supply a
replacement or refund the purchase money but shall not be liable if the Products have been modified or used or maintained otherwise
than in accordance with R&G's or manufacturer's instructions and good engineering practice or if the defect arises from accident or
neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be
liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or
the fitting or service concerned. These terms do not affect the Buyer's statutory rights.
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were
purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-
sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value
exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No returns of
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
ISSUE 2
15/03/2011 (NSY)
CONSUMER NOTICE
R&G Racing
www.rg-racing.com
Email:
info@rg-racing.com