Product Certification - Oursson AM6244 Manuel D'instructions

Causes
System overheated
Operating temperature of the coffee machine
in the room is below 10° C
Making beverages is not available
Pressure is too high when making coffee
Making beverages is not available
Problem with brewing unit. Making beverages
is not available
Problem Cause
The coffee cup was not pre-heated
The coffee temperature is
Several minutes have passed since
too low
the last time of coffee making, so the
brewing unit and the internal pipes are
already cold.
The Coffee bean powder is too fine, or it
has been ground too fine.
Coffee only comes out
from the coffee spout drop
by drop
Brewing unit filter was blocked.
The grinder arising noises There are foreign objects in the grinder.
The milk frother cannot
The milk frother is blocked.
make any milk foam
Milk sprays from the milk The milk frother was not assembled
frother correctly.
Screen always indicates The sheet metals at ends of the drip tray
«EMPTY TRAY» are dirty or wet.
26
Solutions Display
Turn off the coffee machine and
turn it on after an hour.
TEMPERATURE HIGH
Move the coffee machine into a
warm room
TEMPERATURE LOW
Power off, restarting up. If still
unresolved, please pull out the
plug. Contact with Oursson
ERROR 1
customer service center.
Clean the brewing unit
PRESSURE HIGH
Turn off the coffee machine and
VALVE RESET
RESTART MACHINE
turn it on again.
Turn off the coffee machine and
BREW UNIT RESET
turn it on again.
RESTART MACHINE
Solutions
Wash the coffee cup with hot water
before making coffee.
To make many cups of coffee.
Adjust the grinding wheel to a rough
state or use the suitable coffee
powder to make espresso.
Run the brewing unit washing
program.
Make coffee again, if it still failures,
please contact with the Oursson
customer service center.
Clean the milk frother.
Reassemble the milk frother.
Clean the sheet metals according to
CLEANING AND MAINTENANCE.
Problem
Screen always indicates
Coffee grounds in the bottom of the
«INSTALL GOUNDS
machine are not cleaned.
CONTAINER»
Screen always indicates
«FILL WATER TANK» The water tank inductor is trapped.
TRANSPORTATION
• Please save the packaging of the coffee machine for
future transportations.
• Make sure to empty water inside the machine before
transportation, otherwise, it will damage the machine.
• After emptying the waterway, please wipe dry the
machine both inside and outside.
• Once the empty waterway program was
executed, the system will rerun to the program
of «first-time use», when the coffee machine is
used again, you must complete all steps from the
FIRST-TIME USE.
• Display «READY»
• Remove the water tank from the coffee machine.
Specifications
Model
Power consumption, W
Rated voltage
Coffee mill power, W
Pump pressure, bar
Water tank volume, L
Beans tank capacity, g
Thick tank volume
Brew block volume, g
Adjustment height of coffee spout
Power cord length, m
Temperature:
Humidity:
Level of protection
Dimensions, mm
Weight, kg

PRODUCT CERTIFICATION

For information on product certification, see http://www.oursson.com/rus/ru/about/partners/certificates/#tab0 or ask seller
for a copy.
Products should be stored in dry, ventilated warehouses at temperatures below
*
Reparation must be performed only by a qualified personnel authorized by OURSSON AG service
center.
Cause Solutions
Clean the coffee grounds according to
CLEANING AND MAINTENANCE.
Clean the water tank according to
CLEANING AND MAINTENANCE.
Display «FILL WATER TANK»
• Press and hold for 2 seconds, display will say
«EMPTY UNIT».
• Steam and water will come out from the spouts.
• After the water is drained, the coffee machine will
turn off.
1 2
READY
FILL WATER TANK
3 4
EMPTY UNIT
AM6244
max 1200
220-240 V~; 50 Hz
20
19
1.8
250
15 cups
7 - 14
from 80 up to 140 mm
1.2
Operating +15°C to +35°C
Storage and transportation - 25°C to +55°C
Operating 15-75%
Storage and transportation 15-75%
I
450×302×370
13
- 25°С.
27