Kenwood DPX-M3300BT Mode D'emploi page 27

Audio Settings
[MANUAL EQ] Adjusts your own sound settings for each source.
• The settings are stored to [USER] in [PRESET EQ].
• The settings made may affect the current settings of [EASY EQ].
[62.5HZ] [LEVEL]
[BASS EXTEND] [ON]: Turns on the extended bass. ; [OFF]: Cancels.
[100HZ]/[160HZ]/ [LEVEL –9] to [LEVEL +9] ([LEVEL 0]): Adjusts the level to memorize
[250HZ]/[400HZ]/ for each source.
[630HZ]/[1KHZ]/ (Before making an adjustment, select the source you want to adjust.)
[1.6KHZ]/[2.5KHZ]/
[4KHZ]/[6.3KHZ]/
[10KHZ]/[16KHZ]
[Q FACTOR] [1.35]/[1.50]/[2.00]: Adjusts the quality factor.
[PRESET EQ] [NATURAL]/[ROCK]/[POPS]/[EASY]/[TOP40]/[JAZZ]/[POWERFUL]/
[USER]: Selects a preset equalizer suitable to the music genre.
• When the display demonstration is activated ([ON] is selected
initially, page 23), [ROCK] is automatically selected as the
[PRESET EQ].
– If you set [DEMO MODE] to [OFF] (page 23), [NATURAL] is
selected as the default setting for [PRESET EQ].
(Select [USER] to use the settings made in [EASY EQ] or
[MANUAL EQ].)
[BASS BOOST] [LEVEL1] to [LEVEL5]: Selects your preferred bass boost level. ;
[OFF]: Cancels.
[LOUDNESS] [LEVEL1]/[LEVEL2]: Selects your preferred low or high frequencies
boost to produce a well-balanced sound at low volume. ;
[OFF]: Cancels.
[SUBWOOFER SET] [ON]: Turns on the subwoofer output. ; [OFF]: Cancels.
[LEVEL –9] to [LEVEL +9] ([LEVEL 0]): Adjusts
the level to memorize for each source.
(Before making an adjustment, select the source
you want to adjust.)
[FADER] (Not applicable if 3-way crossover is selected.) (Page 6)
[R15] to [F15] ([0]): Adjusts the front and rear speaker output balance.
[BALANCE] [L15] to [R15] ([0]): Adjusts the left and right speaker output balance.
[VOLUME OFFSET] [–15] to [+6] ([0]): Presets the initial volume level of each source by
comparing to the FM volume level.
(Before adjustment, select the source you want to adjust.)
[SOUND EFFECT]
[SOUND RECNSTR] (Not applicable for RADIO source and AUX source.)
(Sound [ON]: Creates realistic sound by compensating the high-frequency
reconstruction) components and restoring the rise-time of the waveform that are lost in
audio data compression. ; [OFF]: Cancels.
[SPACE ENHANCE] (Not applicable for RADIO source.)
[SMALL]/[MEDIUM]/[LARGE]: Virtually enhances the sound space. ;
[OFF]: Cancels.
[SND REALIZER] [LEVEL1]/[LEVEL2]/[LEVEL3]: Virtually makes the sound more
realistic. ; [OFF]: Cancels.
[STAGE EQ] [LOW]/[MIDDLE]/[HIGH]: Virtually adjusts the sound position heard
from the speakers. ; [OFF]: Cancels.
[DRIVE EQ] [ON]: Boosts the frequency to reduce the noise heard from outside the
car or running noise of the tyres. ; [OFF]: Cancels.
[SPEAKER SIZE] Depending on the crossover type you have selected (see "Change the
crossover type" on page 6), 2-way crossover or 3-way crossover
setting items will be shown. (See "Crossover settings" on page 20.)
[X ' OVER]
By default, 2-way crossover type is selected.
[DTA SETTINGS]
For settings, see "Digital Time Alignment settings" on page 21.
[CAR SETTINGS]
• For 2-way crossover: [SUB-W LEVEL]/[SUBWOOFER SET] is selectable only if
[SWITCH PREOUT] is set to [SUBWOOFER]. (Page 5)
• [SUB-W LEVEL] is selectable only when [SUBWOOFER SET] is set to [ON].
19
ENGLISH