Télécharger Imprimer la page

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

MATERIALS
A
1
Crossbar
B
2
Sidearms
C
2
Extension Bars
D
20
M10 x 35 x 1.5 Bolts, Washers, Lock Washers & Nuts (Grade 10.9)
E
2
M12 x 40 x 1.75 Bolts, Nyloc Nuts and Protection Caps 4off (Grade 10.9)
E1
6
M12 x 45 x 1.75 Bolts, Nyloc Nuts (Grade 10.9)
F
2
End Caps
G
2
Coupling Packer
H
2
M16 x 2.00 x 60 Bolts, Lock Washers & Nuts (Grade 8.8)
This towbar must be used with either a Witter Towball (part number Z11) or Universal Coupling Z46 or Z32, Class A50-1 or A50-X
towball, which dimensionally conforms to A50-1 with a 'D' and 'S' value greater than or equal to that of the towbar.
FITTING
1.
This towbar is designed to fit the vehicle chassis and any light clusters or lighting boards will need to be removed and
adapted to enable re-fitment.
2.
Loosely attach Sidearms (B) to the outside faces of the chassis using bolts (D).
3.
Loosely attach Crossbar (A) along with Extensions (C) to the Sidearms using bolts (E) & (E1). NB. Bolts (E) are shorter
in length than (E1) to allow for Protection Caps to be fitted.
4.
Attach End Caps (F) to Extension Bars.
5.
Fully tighten bolts to recommended torque settings, ensuring central profile face is vertical.
6.
Attach towball & Coupling Packer (G) (if required) using M16 bolts (H).
7.
Activate Tipper and check for adequate clearance.
Recommended torque settings: Grade 8.8 bolts: M16 - 200 Nm
Fitting
Instructions
Grade 10.9: M12 - 120Nm, M10 - 70Nm
µW0001CL115-FIT$0113071600007Ä
W0001CL115-FIT$011307160000
For Mitsubishi Canter (2010 - )
3.5 tonne Chassis Cab (N1 cat.)
Tipper & Dropside 750mm Chassis
TOWBAR
CL115

Publicité

loading

Sommaire des Matières pour Witter CL115

  • Page 1 M16 x 2.00 x 60 Bolts, Lock Washers & Nuts (Grade 8.8) This towbar must be used with either a Witter Towball (part number Z11) or Universal Coupling Z46 or Z32, Class A50-1 or A50-X towball, which dimensionally conforms to A50-1 with a ‘D’ and 'S' value greater than or equal to that of the towbar.
  • Page 2 IMPORTANT INFORMATION – MUST BE HANDED TO END USER When operating the body tipping system it is essential to ensure that the tailgate does not become obstructed by the towball or towbar coupling during the tipping operation. Failure to do so could result in damage to the tailgate, towbar or the vehicle chassis.
  • Page 3 Boulons M16 x 2.00 x 60, rondelles freins et écrous (classe 8.8) Remarque : Cet attelage doit être utilisé avec une boule de remorquage Witter (référence produit Z11) ou une boule de remorquage Classe A50-1 ou A50-X se conformant dimensionnellement à A50-1 avec une valeur ‘D’ et 'S' supérieure ou égale à...
  • Page 4 INFORMATION IMPORTANTE - DOIT ETRE DONNER A L'UTILISATEUR FINAL Lorsque vous utilisez le système de basculement de la benne, il est essentiel de veiller à ce que le hayon ne devient obstrué par la boule d'attelage ou accouplements lors de l'opération de basculement Ne pas le faire pourrait entraîner des dommages au hayon, le crochet d'attelage ou le châssis du véhicule.