Publicité
Les langues disponibles
Les langues disponibles
Page 8 of 12
FITTING INSTRUCTION (REAR INDICATORS)
•
Remove the pillion seat using the key.
•
Disconnect the indicator and licence plate illuminator wiring plug sockets.
•
Remove the four nuts that hold the original licence plate bracket from under
the pillion seat as arrowed in picture 1A.
•
With the original licence plate bracket removed, remove the two screws
arrowed in pictures 2A and 3A.
•
Remove the four bolts and four screws arrowed in picture 4A.
•
Remove the cable cover/support for access to the original indicators and
wiring as shown in picture 5.
•
Remove the spreader/location plate arrowed in pictures 6 and 7.
•
Gently squeeze the indicator stem and remove the indicator as shown in
picture 8.
•
Repeat for the removal of the other indicator.
•
Position one of the indicator adaptors (item 1 –I0036) onto the wiring of the
indicator as shown in picture 10 (ensuring the raised centre profile will locate
into the original bracket), place the indicator with the adaptor plate into the
original indicator mount bracket as shown in picture 11.
•
Place another of the adaptor plates onto the wiring, ensuring the raised centre
profile locates into the bracket, before fitting the flanged nut supplied, as
shown in picture 12.
•
Feed the indicator wiring through one of the nut/wire covers (item 2) as
shown in picture 13 (it helps if a small amount of liquid detergent is used)
and position the nut cover over the nut (repeat the above for the opposite
indicator).
•
Fit one length of heat-shrink (item 4) over the wires of each indicator so the
heat-shrink fits over the stem of the nut/wire cover and gently heat until the
heat-shrink contracts to the wiring and nut/wire cover as shown in picture
14.
•
Repeat the above for the opposite indicator.
•
Connect both indicators to the original plug sockets using the supplied
indicator connectors (item 3). It is a good idea the check the indicators at
this stage if illumination fails please swap the bullet connections around
(please note you may have to use resistors to achieve the correct flash rate).
•
Refit the cable cover support as original.
•
Refit the licence plate bracket as original.
•
Please recheck the operation of all lights before riding.
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do not
diminish their performance or visual appeal and supplying them in such state shall conform to the order. The Buyer acknowledges no representation
or warranty (other than as to title) has been given or will apply to the Products other than those in R&G's order or confirmation and the Buyer
confirms it has chosen the Products as being of merchantable quality and suitable for its particular purposes. Where R&G fits the Products or
undertakes other services it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has been disturbed.
The Buyer is responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective
Products R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have been mod ified
or used or maintained otherwise than in accordance with R&G's or manufacturer's instructions and good engineering practice or if the defect arises
from accident or neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be
liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or
service concerned. These terms do not affect the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were purchased
direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-sellable condition, in the
opinion of R&G. All returns are subject to a 25% restocking and handling fee (25% of the gross value exc. P&P – at the prevailing price at time of
purchase). The customer must pay any and all carriage charges. No returns of discontinued products, unless within 14 days of purchase. This policy
does not affect your statutory rights and does not refer to faulty goods.
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
ISSUE 1 23/11/2020 (NSY)
CONSUMER NOTICE
R&G RETURNS POLICY (NON-FAULTY GOODS)
R&G
www.rg-racing.com
IA/IAS0019
Email:
info@rg-racing.com
Publicité
