R&G AB0011BK Mode D'emploi page 6

20mm long) over the exposed end of the thread, ensuring the larger diameter end sits against the
mounting plate of the crash bar as before.

This assembly can now be offered up to the right side of the bike as shown in picture 3. Tighten
the bolts loosely just to hold the crash bar in place whilst continuing assembly.

Take the spanning tube (item 11 – SPT01) and slide it into the now fitted right hand side crash bar,
as shown in picture 4. Do not insert any bolts at this stage.

On the left side of the bike, remove the three T20 Torx screws that mount the oil filler to the
plastic side pod before gently pulling downward and clear, as shown in picture 5.

Locate the oil filler spacer (item 9 – S0734 – 16mm thick) over the filler cap and align the holes,
as shown in picture 6.

Re-locate into the plastic side pod and fit the three 6 x 30mm long coarse threaded bolts (item 10)
before tightening into place, as shown in picture 7.

Remove the two T45 bolts which secure the plastic side pod to the engine/frame, as shown in
picture 8.

Take the left hand side adventure bar (item 8 – CB031) and assemble the same way as the right
side, ensuring the longer bolt fits in the top mount and the shorter bolt fits the lower mount. Use
the remaining two spacers (item 7 – S0142 – 24mm long) with the larger diameter sitting against
the mounting plates.

This assembly can now be offered up to the left side of the bike as shown in picture 9. Ensure the
front horizontal tube connects into the already fitted spanning tube and both ends of the spanning
tube are fully engaged within each crash bar, before tightening the bolts loosely.

Take the two M6 x 28mm long button head bolts (item 12) and locate through the two holes on the
spanning tube, connecting them to the crash bars (this may require a little bit of movement for the
holes to align) and then fit one M6 washer (item 13) and one M6 domed nut (item 14) to either
bolt, as shown in picture 11.

Ensure the adventure bars are correctly located before tightening all four bolts. There is some
adjustment built into the mounts to allow the bars to be setup identically either side. When
correctly mounted, tighten the four bolts to 40N/m and ensure the two nuts are fully tightened on
the spanning tube.

Fit the four 17mm hex head plastic caps (item 5) to the four bolt heads to protect them from the
elements and give a clean look.
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order. The
Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than those
in R&G's order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for
its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify
any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on the
motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its option either supply a
replacement or refund the purchase money but shall not be liable if the Products have been modified or used or maintained otherwise
than in accordance with R&G's or manufacturer's instructions and good engineering practice or if the defect arises from accident or
neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be
liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or
the fitting or service concerned. These terms do not affect the Buyer's statutory rights.
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
ISSUE 1 21/01/2014 (AR)
CONSUMER NOTICE
R&G Racing
www.rg-racing.com Email: info@rg-racing.com