Main Screen - nVent RAYCHEM HWAT-ECO-GF Manuel D'installation, D'utilisation Et D'entretien

Main Screen

EN
HOT WATER MAINTENANCE
FR
NOW
131°F
Contains 3 areas:
SYSTEM
INFO, RESET, SERVICE, TEST....
• Actual Maintain temperature (red area)
HEATING CABLE & PIPE
• Next event temperature (grey area)
CABLE TYPE, PIPE DAIMETER,...
• Hot water storage temperature
GENERAL SETTINGS
COUNTRY, LANGUAGES, UNITS,...
(white area- if boiler sensor is connected and active)
WATER TEMP. & PROGRAM
HOT WATER MAINTENANCE
Additional icons for settings, relay (ON/OFF), key lock or warning will
APPARTMENT, MAINTAIN, ECONOMY,....
be displayed.When Lock is "on" a password is needed to access the
parameter menus.
NOW
After the correct 4 number password is entered, each parameter in the
131°F
setup can be changed. The unit locks again after a 10 min. time out (no
INFO
keys pressed).
TEST PROGRAM
SETTINGS
RESET
SERVICE
SYSTEM
STATUS
INFO, RESET, SERVICE, TEST....
HEATING CABLE & PIPE
CABLE TYPE, PIPE DAIMETER,...
GENERAL SETTINGS
COUNTRY, LANGUAGES, UNITS,...
WATER TEMP. & PROGRAM
APPARTMENT, MAINTAIN, ECONOMY,....
SELECT CABLE TYPE
SYSTEM
SELECT PIPE DIAMETER
SELECT INSULATION THICKNESS
INFO
SELECT AMBIENT TEMPERATURE
TEST PROGRAM
INFO
SELECT BOILER SENSOR RESET
TEST PROGRAM
SERVICE
SELECT BOILER CUT-OFF TEMPS. RESET
STATUS
SERVICE
STATUS
KEYLOCK FEATURE
SELECT CABLE TYPE
Info
SELECT PIPE DIAMETER
SELECT CABLE TYPE
SELECT INSULATION THICKNESS Test
program
SELECT PIPE DIAMETER
SELECT AMBIENT TEMPERATURE
SELECT INSULATION THICKNESS
SELECT BOILER SENSOR
Reset
SELECT AMBIENT TEMPERATURE
SELECT BOILER CUT-OFF TEMPS.
SELECT BOILER SENSOR
Service
SELECT BOILER CUT-OFF TEMPS.
|
20 nVent.com/RAYCHEM
SETTING
HOT WATER MAINTENANCE
SYSTEM
NOW
131°F
SETTING
SETTING
SYSTEM
INFO, RESET, SERVICE, TEST....
HEATING CABLE & PIPE
HEATING CABLE & PIPE
CABLE TYPE, PIPE DAIMETER,...
GENERAL SETTINGS
COUNTRY, LANGUAGES, UNITS,...
WATER TEMP. & PROGRAM
APPARTMENT, MAINTAIN, ECONOMY,....
SYSTEM
SYSTEM
HEATING CABLE & PIPE
General info about the unit, name, commissioning date,
HEATING CABLE & PIPE
firmware version, nVent contact info per country.
The test program runs for 30 minutes, during which
all parameters will be ignored to check the heating
cable and the connection on site. You can stop the test
program at any time.
Select "Yes" to activate the Quick install menu and return
all settings to factory settings.
Quick start process restarts automatically.
Access for nVent SERVICE TEAM
02:14 p.m.
NEXT
131°F
ECONOMY TEMP
AT 05:00 p.m.
BOILER
140 °F
14 : 17
02:14 p.m.
NEXT
02:14 p.m.
131°F
14 : 17
NEXT
ECONOMY TEMP
131°F
AT 05:00 p.m.
BOILER
ECONOMY TEMP
140 °F
AT 05:00 p.m.
BOILER
140 °F
14 : 17
14 : 17
HWAT-R2
DN 25
14 : 17
40 MM
20 °C
ON
35/85 °C
14 : 17
HWAT-R2
DN 25
HWAT-R2
40 MM
DN 25
20 °C
40 MM
ON
20 °C
35/85 °C
ON
35/85 °C
SELECT LANGUAGE
grey area
SELECT COUNTRY
SELECT DATE
white area
SELECT TIME
SELECT ALARM
red area
SELECT SAVING TIME
SELECT WATER TEMPERATURE
SELECT PROGRAM
SELECT LANGUAGE
PROGRAM TIMER
SELECT COUNTRY
SELECT LANGUAGE
SELECT DATE
SELECT COUNTRY
SELECT TIME
SELECT DATE
SELECT ALARM
SELECT TIME
SELECT SAVING TIME
SELECT ALARM
14 : 17
SELECT SAVING TIME
SELECT WATER TEMPERATURE
SELECT PROGRAM
SELECT WATER TEMPERATURE
PROGRAM TIMER
SELECT PROGRAM
PROGRAM TIMER
14 : 17
14 : 17
GENERA
G
WATER T
W