Main Screen - nVent RAYCHEM HWAT ECO Mode D'emploi

MAIN SCREEN

HOT WATER MAINTENANCE
NOW
contains 3 areas:
SYSTEM
INFO, RESET, SERVICE, TEST....
1. Actual maintain temperature (red area)
HOT WATER MAINTENANCE
2. next event temperature (grey area)
HEATING CABLE & PIPE
3. Hot water storage temperature
CABLE TYPE, PIPE DAIMETER,...
(white area- if boiler sensor is connected and active)
GENERAL SETTINGS
NOW
COUNTRY, LANGUAGES, UNITS,...
additional icons for settings, relay (on/oFF), key lock or warning will be displayed.
when lock is "on" a password is needed to access the parameter menus.
WATER TEMP. & PROGRAM
after the correct 4 number password is entered, each parameter in the setup can be
APPARTMENT, MAINTAIN, ECONOMY,....
changed. the unit locks again after a 10 min. time out (no keys pressed).
SETTINGS
INFO
TEST PROGRAM
SYSTEM
INFO, RESET, SERVICE, TEST....
RESET
HEATING CABLE & PIPE
CABLE TYPE, PIPE DAIMETER,...
SERVICE
GENERAL SETTINGS
COUNTRY, LANGUAGES, UNITS,...
STATUS
WATER TEMP. & PROGRAM
APPARTMENT, MAINTAIN, ECONOMY,....
SYSTEM
INFO
SELECT CABLE TYPE
TEST PROGRAM
SELECT PIPE DIAMETER
INFO
RESET
SELECT INSULATION THICKNESS
TEST PROGRAM
SERVICE
RESET
SELECT AMBIENT TEMPERATURE
STATUS
SERVICE
SELECT BOILER SENSOR
STATUS
SELECT BOILER CUT-OFF TEMPS.
info
SELECT CABLE TYPE
SELECT PIPE DIAMETER
Test
SELECT CABLE TYPE
programme
SELECT INSULATION THICKNESS
SELECT PIPE DIAMETER
SELECT AMBIENT TEMPERATURE
reset SELECT INSULATION THICKNESS
SELECT BOILER SENSOR
SELECT AMBIENT TEMPERATURE
SELECT BOILER CUT-OFF TEMPS.
service SELECT BOILER SENSOR
SELECT BOILER CUT-OFF TEMPS.
12 | nVent.com
SETTING
HOT WATER MAINTENANCE
NOW
SYSTEM
SETTING
SETTING
SYSTEM
INFO, RESET, SERVICE, TEST....
HEATING CABLE & PIPE
CABLE TYPE, PIPE DAIMETER,...
GENERAL SETTINGS
COUNTRY, LANGUAGES, UNITS,...
WATER TEMP. & PROGRAM
SYSTEM
APPARTMENT, MAINTAIN, ECONOMY,....
HEATING CABLE & PIPE
SYSTEM
HEATING CABLE & PIPE
general info about the unit, name, commissioning date,
HWAT-M
HEATING CABLE & PIPE
firmware version, nVent contact info per country.
DN 25
The test programme runs for 30 minutes, during which all
parameters will be ignored to check the heating cable and
40 MM
the connection on site. you can stop the test programme
at any time.
20 °C
select "yes" to activate the Quick install menu and return
all settings to factory settings.
ON
Quick start process restarts automatically.
35/85 °C
Access for nVent sErViCE TEAm
14 : 14
NEXT
ECONOMY TEMP
AT 17:00
BOILER
14 : 17
14 : 14
NEXT
ECONOMY TEMP
NEXT
AT 17:00
BOILER
ECONOMY TEMP
14 : 17
AT 17:00
BOILER
14 : 17
14 : 17
14 : 17
HWAT-M
DN 25
40 MM
20 °C
ON
35/85 °C
14 : 17
HWAT-M
DN 25
40 MM
20 °C
ON
35/85 °C
SELECT LANGUAGE
grey area
SELECT COUNTRY
SELECT DATE
white area
SELECT TIME
SELECT ALARM
red area
SELECT SAVING TIME
SELECT LANGUAGE
SELECT WATER TEMPRATURE
14 : 14
SELECT COUNTRY
SELECT LANGUAGE
SELECT PROGRAM
SELECT DATE
SELECT COUNTRY
PROGRAM TIMER
SELECT TIME
SELECT DATE
SELECT ALARM
SELECT TIME
SELECT SAVING TIME
SELECT ALARM
14 : 17
SELECT SAVING TIME
SELECT WATER TEMPRATURE
SELECT PROGRAM
SELECT WATER TEMPRATURE
PROGRAM TIMER
SELECT PROGRAM
PROGRAM TIMER
14 : 17
14 : 17
GENERA
WATER T