Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
2. Technical Information
This is a clean burning stove, which has a minimal
emission of soot particles and un-burnt gases (e.g.
CO). Use exclusively clean and dry wood.
Material:
Surface treatment
door/doorframe:
Fuel:
Operating range:
Draught system:
Combustion system:
Heating area:
Flue outlet:
Flue:
Weight Trio I
Weight Trio II
Weight Trio III
3. Distance to combustible material
(FIG 1) Ensure that the safety distances are
respected. The distance from the front of the stove
to furniture needs to be at least 1 metre. When
connecting a steel chimney to the top outlet use the
security distances required from the manufacturer.
4. Fresh air supply
Additional supply of combustion air can be added
directly by channelling it directly from the outside, or
indirectly by a vent in the exterior wall of the room
where the stove is situated.
5. Assembly
The following tools are necessary:
•
5 mm allen key
•
6 mm allen key
•
caulking gun (for the stove cement)
•
an adjustable spanner
•
screwdriver / star screwdriver
Functions (FIG 2-10)
FIG 2: The door is opened by gently pressing (about
10 mm) and releasing the handle. Close the door
by pressing the handle together with the door. If the
handle is pressed too much the door will open again.
FIG 4: The air vent control is adjusted by moving the
wheel on the right side of the door.
FIG 5: Remove the transportation safety device and
lift the smoke baffle up into its position.
FIG 7: The cold-handle is fastened under the stove by
magnet. On Trio II it is fastened on the inside of the
door of the pedestal.
FIG 8: Remove ashes by shaking the ash grate with
Cast iron & sheet steel
UHT Varnish
Wood logs, 30 cm
7,5 kW at nominal
Air vent control
Secondary combustion
(clean burning)
55-110 m²
Top and posterior
Ø 150 mm
130 kg
135 kg
125 kg
the cold-handle, or alternatively with a spade.
FIG 9: The ashtray is pulled out in front with the
cold-handle.
FIG 10: Adjusting the door. Unscrew both screws,
position correctly the door and fasten the screws
again.
Thermotte® Plates
There are six Thermotte® plates (Fig 6), that are
already mounted inside the stove. Should it be
necessary to renew one or several plates, contact
your dealer. See chapter on maintenance.
A.
Smoke baffle
B.
Side plate
C.
Side plate
D.
Back plate
E.
Ash grate
F.
Ash tray
G.
Bottom plate
H.
Log-stopper
In case the Thermotte® plates need to be uninstalled,
do as follows (NB! Handle the plates with care as they
easily break):
1. Lift up the smoke baffle (A) with one hand
2. Remove side plate B or C
3. Take out the smoke baffle (A) and remove
remaining parts
Flue Outlet Collar
Trio is delivered as standard with a top flue outlet
collar. In order to change to a posterior mounted flue
outlet (FIG 11-15):
1.
Remove the entire loose top lid
2.
Unscrew the flue outlet collar with a 5 mm allen key
3.
Remove the perforated decoration lid in the back
with a hammer, or saw it out with a hacksaw
4.
Unscrew the sheet steel lid
5.
Fasten the collar on the posterior flue outlet
6.
Fasten the sheet steel lid on the top flue outlet
7.
Position the top lid
Fresh Air Supply
FIG 16: Tighten the locking band with a screwdriver
FIG 17-20: Different options for fresh air supply
English
11
Publicité
Table des Matières
