Operation Of Wireless Remote Control; Special Function; Changing Batteries - mundoclima MUPR-HG Instructions D'installation

OPERATION OF WIRELESS REMOTE CONTROL

Be sure that there are no obstructions between receiver and remote controller; Don't drop or throw the remote control; Don't let any liquid in the remote control and put the remote control directly under the sunlight or any place where is very hot.
ON/OFF button: Press this
button, the unit will be turned
on, press it once more, the
unit will be turned off. When
turning on or turning off the
unit, the Timer, Sleep
function will be canceled,but
the presetting time is still
remained.
MODE button: Press this
1 2
button, Auto, Cool,Dry, Fan,
Heat mode can be selected
circularly.Auto mode is
default while power on.
3 4
U n d e r A u t o m o d e , t h e
temperature will not be
5 6
displayed; Under Heat
7 9
mode, the initial value is
28°C(82°F);Under other
8 12
modes, the initial value is
10 11 25°C(77°F).
SLEEP button : Press this button, Sleep On and Sleep Off
can be selected. After powered on,Sleep Off is defaulted.
After the unit is turned off, the Sleep function is canceled.
After Sleep function set up, the signal of Sleep will display. In
this mode, the time of timer can be adjusted. Under Fan and
Auto modes, this function is not available.
FAN Press this button, Auto, Low, Middle, High speed can be
circularly selected. After powered
on,Auto fan speed is default. Under
Dehumidify mode, Low fan speed
only can be set up.
CLOCK button : Press this button, the clock can be set up,
signal blink and display.Within 5 seconds, the value can be
adjusted by pressing + or - button, if continuously press this
button for 2 seconds above, in every 0.5 seconds, the value
on ten place of Minute will be increased 1. During blinking,
repress the Clock button, signal will be constantly displayed
and it denotes the setting succeeded. After powered on,
12:00 is defaulted to display and signal will be displayed. If
there is signal be value is Clock value, otherwise is Timer
Guide for operation
General:
1. After powered on, press ON/OFF button, the unit will start to
1 2
it is powered off, the guide louver of main unit will close
3
5
4
2. Press MODE button, select desired running mode, or press
3. Pressing +or - button, to set the desired temperature. (It is
4. Pressing FAN button, set fan speed, can select AUTO FAN,
5. Pressing button, to select the swing.

Special function

About BLOW funtion:
This function indicates that moisture on
evaporator of indoor unit will be blowed
after the unit is stopped to avoid mould.
1. Having set blow function on: After turning
off the unit by pressing ON/OFF button
indoor fan will continue running for about
10 min. at low speed. In this period,
press blow button to stop indoor fan
directly.
2. Having set blow function off: After turning
off the unit by pressing ON/OFF
button,the complete unit will be off
directly.
About AUTORUN:
When AUTO RUN mode is selected, the
setting temperature will not be displayed
on the LCD, the unit will be in accordance
with the room temp. automatically to select
the suitable running method and to make
ambient comfortable.
About TURBO funtion:
If start this function, the unit will run at
super-high fan speed to cool or heat
quickly so that the ambient temp.
approachs the preset temp. as soon as
value. displayed that denotes the current time
LIGHT button: Press this button to select LIGHT on or off in
the displayer. When the LIGHT on is set,the icon will be
displayed and the indicator light in the displayer will be on.
When the LIGHT off is set, the icon will be displayed and the
indicator light in the displayer will be off.
BLOW button: Press this button, can turn on or turn off the
drying.In Cool and Dehumidifying mode, press this button
and will display "BLOW", at this time the Blow is turned on. If
repress this button,"BLOW" will be concealed, at this time the
Blow function is turned off. After powered on, Blow OFF is
defaulted.
When operating the ON/OFF button, or switching mode to
Cool or Dehumidifying mode,the Blow function will keep the
original status. If unit is turned off, Blow OFF only can be set
up and send the signal. In Auto, Fan as well as Heat mode,
Blow function can not be set up and there is no "BLOW"
displaying.
- button: Presetting temperature can be decreased. Press
this button, the temperature can be set up, continuously
press this button and hold for two seconds, the relative
contents can quickly change, until unhold this button and
send the order that the °C (°F) signal will be displayed all the
time. The temperature adjustment is unavailable under the
Auto mode, but the order can be sent by if pressing this
button.
+ button: For presetting temperature increasing. Press this
button,can set up the temperature, when unit is on .
Continuously press and hold this button for more than 2
seconds, the corresponding contents will be changed rapidly,
until unpress the button then send the information,°C (°F)is
displaying all along. In Auto mode, the temperature can not
be set up, but operate this button can send the signal.
Centigrade setting range :16-30; Fahrenheit scale setting
range 61-86.
TEMP button: Press this button, could select displaying the
i n d o o r s e t t i n g t e m p e r a t u r e o r i n d o o r a m b i e n t
temperature.When the indoor unit firstly power on it will
display the setting temperature, if the temperature's
displaying status is changed from other status to"
displays the ambient temperature, 5s later or within 5s, it
receives other remote control signal that will return to display
the setting temperature. if the users haven't set up the
temperature displaying status,that will display the setting
temperature.(This function is applicable to partial of models)
After powered on, the setting temperature displaying is
defaulted, (according to customers requirements to display, if
there is no requirement that will default to display the
presetting temperature and there is no icon displayed on
wireless remote control). Press this button, (When
run.(Note: When
automatically.)
COOL or HEAT mode to enter into the corresponding
operation directly.
unnecessary to set the temp. at AUTO mode.)
LOW, MID and HIGH.
possible.
About LOC K :
Press +and - buttons simultaneously to
lock or unlock the keyboard. If the remote
controller is locked, the icon
displayed on it, in which case, press any
button, the mark will flicker for three times.
If the keyboard is unlocked, the mark will
disappear.
About SWING up and down:
1. Press swing up and down button
continuously more than 2s,the main unit
will swing back and forth from up to down,
and then loosen the button, the unit will
stop swinging and present position of
guide louver will be kept immediately.
2. Under swing up and down mode, when
the status is switched from off to , if press
this button again 2s later, status will switch
to off status directly; if press this button
again within 2s,the change of swing status
will also depend on the circulation
sequence stated above.
About switch between °F a °C :
Under status of unit off, press MODE and -
buttons simultaneously to switch °C and °F.
MUPR-HG
NOTE
___
4

Changing batteries

1. Slightly to press the place with ,
along the arrowhead direction to
push the back cover of wireless
remote control. (As show in figure)
2. Take out the old batteries. (As show
will be
in figure)
3. Insert two new AAA1.5V dry
batteries, and pay attention to the
polarity. (As show in figure)
4. Attach the back cover of wireless
remote control. (As show in figure)
NOTE: When changing the batteries,
do not use the old or different
batteries,otherwise, it can cause the
malfunction of the wireless remote
control.If the wireless remote control
will not be used for a long time, please
take them out, and don't let the
leakage liquid damage the wireless
remote control. The operation should
be in its receiving range. It should be
placed at where is 1m away from the
TV set or stereo sound sets. If the
wireless remote control can not
operate normally, please take them
out, after 30s later and reinsert, if they
GB
displaying ___ ) , will display presetting temperature; (when
displaying ___ ) will display indoor ambient temperature
current displaying status will not be changed. If current
displays indoor ambient temperature , if received the other
remote control signal, it will display presetting temperature,
5s later, will back to display the ambient temperature. (This
function is applicable to partial of models)
TURBO button: In Cool or Heat mode, press this button can
turn on or turn off the Turbo function. After turned on the Turbo
function, its signal will be displayed. When switching the
mode or changing fan speed, this function will be canceled
automatically.
SWING UP AND DOWN button: Press this button, to set up
swing angle, which circularly changes as below:
This is an universal use remote controller. Ifremote controller
sends the following threekinds of status that the swing status
of mainunit will be:
When the guide louver start to swing up and down, if turn off
the Swing, the air guide louver will stop at current position.
which indicates the guide louver swings upand down
between that all five positions.
TIMER ON button: Timer On setting: Signal "ON" will blink
and display, signal will conceal, the numerical section will
become the timer on setting status. During 5 seconds blink,
by pressing + or - button to adjust the time value of numerical
section, every press of that button, the value will be increased
or decreased 1 minute. Hold pressing +or - button, 2 seconds
later,
it quickly change, the way of change is: During the initial 2.5
seconds, ten numbers change in the one place of minute,
then the one place is constant, ten numbers change in the
", tens place of minute at 2.5 seconds speed and carry. During
5s blink, press the Timer button, the timer setting succeeds.
The Timer On has been set up, repress the timer On button,
the Timer On will be canceled. Before setting the Timer,
please adjust the Clock to the
current actual time.
TIMER OFF button: Once press this key to enter into TIMER
OFF setup, in which case the TIMER OFF icon will blink. The
method of setting is the same
Optional:
1. Press SLEEP button, to set sleep.
2. Press TIMER ON and TIMER OFF button,
can set the scheduled timer on or timer
off.
3. Press LIGHT button, to control the on and
off of the displaying part of the unit (This
function may be not available for some
2
units).
4. Press TURBO button, can realize the ON
3
and OFF of TURBO function.
1
cannot normally run, please change
them.
___ ,
14